Larson Electronics Explosion Proof Class I, Div. II LED Fixture - 4 foot, 2 T-Style LED Lamps - Emergency Ballast HAL-EMG-48-2L-LED-G2

Made in the USA

The Larson Electronics HAL-EMG-48-2L-LED-G2 Hazardous AreaÊLED Light Fixture is NRTL Listed for United States and Canada Class 1 Division 2 Groups A, B, C and D - NRTL Certified to UL 1598A listed,Êhas a T4C temperature ratingÊand ideal for open air hazardous locations where flammable chemical/petrochemical vapors may be occasionally encountered.

The HAL-EMG-48-2L-LED-G2 fixture is a 4 foot long, 2 lamp, Class 1 Division 2 Groups A, B, C and D hazardous area LED light that takes the reliability and efficiency of a fluorescent fixture and adds even longer lamp life and efficiency with high output LEDs. This fixture is T4C temperature rated and comes standard with our high powerÊ28 wattÊG2 LED lamps. The lamps are protected by an aluminum framed hinged glass door secured with four turn latches and the fixture is constructed of copper free aluminum alloy. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish.

This fixture can be configured to run on 120 to 277VAC as well as 12-24VDC and is NRTL Certified to U.L. 595 and UL 1598A Marine Type approved for use marine environments. The HAL-EMG-48-2L-LED-G2 is weatherproof and provides operators in hazardous locations with a highly efficient, reliable and affordable lighting solution for open areas where flammable chemicals and vapors my occasionally be present.

This light works, mounts and is wired like our HAL-48-2L-LED-G2 explosion proof LED light fixtures. The main difference is that we add a battery backup unit that addsÊemergency light functionality to the fixture. This hazardous area emergency light will run one bulb atÊthe standard suggested 90 minutes after power is lost at 2750 lumens. The light recharges the battery onceÊelectrical power is restored. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.

We have eliminated the ballast normally associated with fluorescent fixtures which reduces overall weight, increases lamp life to an extreme 50,000 hours and helps this LED fixture maintain a T-4C temperature rating. The solid state design of the included LED lamps give this fixture superior resistance to damage from vibrations and extremes in temperature as well as a lamp service life over twice that of standard T5-bulbs. TheÊ28 watt LED lamps produce more illumination than standard T5 bulbs, but draw only 1/3rdÊof the current. The current generation of Larson Electronics LED T-series style bulbs produce 30% more light thanÊstandard T8 bulbs.

This fixture is multi-voltage capable (not multi-tap) and works on the following voltages: 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ, 277 Volts 60 HZ. We also make a 12-24V DC version for low voltage applications (-LV suffix). Our HAL-EMG-48-2L-LED-G2 light fixture is NRTL Listed for U.S. and Canada.

Standard Surface Mount Brackets: Each L bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. Mounting brackets are removable. A single through hole enables the operator to install the light to any surface.

A sliding bracket mount is available so operators can retrofit this LED light fixture to use the pre-existing mounting holes from other fluorescent fixtures. Contact us for the sliding bracket option.

Suggested Applications:ÊAircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Chemical manufacturing, Waste treatment plants, Gas processing plants.