Larson Electronics Explosion Proof C1D2 Dimmable LED Fixture - (3) 4-foot T-Style LED Lamps - Emergency Ballast HAL-EMG-48-3L-LED-D

Made in the USA

The Larson Electronics HAL-EMG-48-3L-LED-D Hazardous Area Dimmable LED Light Fixture is NRTL Listed for United States and Canada Class I, Division 2 Groups A, B, C and D - NRTL Certified to UL 1598A listed and carries a T4C temperature rating. This three-lamp LED fixture is ideal for open air hazardous locations where flammable chemical/petrochemical vapors may be occasionally encountered.

The HAL-EMG-48-3L-LED-D fixture is a 4 foot long, 3 lamp, Class I, Division 2 Groups A, B, C and D hazardous area dimmable LED light that takes the reliability and efficiency of a fluorescent fixture and adds even longer lamp life and efficiency with high output LEDs. This fixture is T4C temperature rated and comes standard with three of our high powered 23-watt dimmable LED lamps that each produce 2,875 lumens. The lamps are protected by an aluminum framed hinged glass door secured with four turn latches and the fixture is constructed of copper free aluminum alloy. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish.

This fixture can be configured to run on voltages from 90-132V AC and is NRTL Certified to U.L. 595 and UL 1598A Marine Type approved for use marine environments. The HAL-EMG-48-3L-LED-D is weatherproof and provides operators in hazardous locations with a highly efficient, reliable and affordable lighting solution for open areas where flammable chemicals and vapors my occasionally be present.

Emergency Battery Backup: This dimmable light works, mounts and is wired like our HAL-48-2L-LED explosion proof LED light fixtures. The main difference is that we add a battery backup unit that adds emergency light functionality to the fixture. This hazardous area emergency light will run one bulb at the standard suggested 90 minutes after power is lost at 2,875 lumens. The light recharges the battery once electrical power is restored. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.

We have eliminated the ballast normally associated with fluorescent fixtures which reduces overall weight, increases lamp life to an extreme 50,000 hours and helps this LED fixture maintain a T-4C temperature rating. The solid state design of the included LED lamps give this fixture superior resistance to damage from vibrations and extremes in temperature as well as a lamp service life over twice that of standard T5-bulbs. The 24 watt LED lamps produce more illumination than standard T5 bulbs, but draw only 1/3rd of the current. The current generation of Larson Electronics LED T-series style bulbs produce 15% more light than standard T5 bulbs.

This fixture is multi-voltage capable (not multi-tap) and works on the following voltages: 90-132V AC. Our HAL-EMG-48-3L-LED-D light fixture is NRTL Listed for U.S. and Canada.

Standard Surface Mount Brackets: Each L bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. Mounting brackets are removable. A single through hole enables the operator to install the light to any surface.

A sliding bracket mount is available so operators can retrofit this LED light fixture to use the pre-existing mounting holes from other fluorescent fixtures. Contact us for the sliding bracket option.

Suggested Applications: Aircraft maintenance, oil drilling rigs, refineries, solvent and cleaning areas, chemical manufacturing, waste treatment plants, gas processing plants and more.