Larson Electronics 1920 Watt 20' Light Mast on 10' Single Axle Trailer - 9' to 20' - 240,000 Lumens - (4) Light Heads

Made in the USA The Larson Electronics LM-20-3S-10TLR-4X400LTL-LED 1,920 watt trailer mounted fold over 3-stage light mast provides a safe and effective way for operators to quickly deploythe equipped high output LED light fixtures to elevations up to twenty feet. The four 400 watt LED lamps produce a wide spread of intense white light, allowing this unit to effectively cover large work areas with high quality illumination. This light tower folds over for easy transportation, features a rotating boom that allows for 360¡ of rotation, and a removable mast head for storing mounted equipment when not in use. The entire assembly is mounted onto a 10` single axle trailer, allowing operators to transport this fold over boom from location to location. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO LIGHT MASTS OR LIGHT TOWERS* This telescoping three stage steel light mast from Larson Electronics’ is designed to allow operators to quickly and safely deploy lighting, cameras, and other electrical equipment in locations where this equipment must be elevated to heights up to 20` for effective coverage. This light boom can be extended to 20` above the trailer floor for maximum area coverage, and collapsed to 9` for applications where a footprint smaller is required. The tower is constructed of square steel tubing with a lower section 7.13` in length and 4" by 4" by 1/8" thick, middle section 7.23` in length and 3" by 3" by 1/8" thick, and an upper section 7.78` in length and 2" by 2" by 1/8" thick. Each section has a minimum 1` foot of overlap. The mast is elevated using an included 1,000lb rated hand winch with 3/16" galvanized steel cable and extended to its full height using a second 1,000 lbs winch. The mast is mounted at the front of a 10` trailer and the mast head hangs above the back of the trailer. Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge Lights: The lighting system on this articulating light mast is comprised of four our of GAU-LTL-400W-LED 400 watt LED lamps producing 54,000 lumens of light each attached to the end of the telescoping pneumatic light boom. These floodlights produce a wide flood light pattern with a combined total of 1,600 watts and 216,000 lumens of light. The GAU-LTL-400W-LED lights are ideal replacements for fragile and hot running 800 watt metal halide lamps, offering increased durability, longer lamp life, and lower power consumption. The entire lighting assembly is connected to the power source via a 4-switch control box. Each light head is on an individual circuit and can be powered on or off independently of the other light fixtures. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units feature individual heat sinks per bank of six LEDs to control heat buildup rather than utilizing a single housing to dissipate heat. This allows for more thorough cooling of the LEDs for extended operating periods. This allows the LEDs to be driven at up to 90% capacity without overheating or visible loss of light output. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 80,000 hours. In addition, should an LED failure occur, these LED flood lights are field serviceable. Each bank of six LEDs can be replaced with the fixture installed. This allows for the tower to stay in operation until repairs can take place, and eliminates the need to remove and disassemble the entire fixture for repairs. Durability: As well as unparalleled heat control, the GAU-LTL-400W-LED series of LED lights from Larson Electronics also offer IP67 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40¡ Celsius to +80¡ Celsius, are waterproof, and resist ingress of dust, dirt and humidity. The housings are formed from die cast aluminum and the optics are high transmission PMMA with 98% light transmittance. The Cree¨ LEDs help these units achieve resistance to vibrations and are rated at 70% lumen maintenance after 80,0000 hours of use. We use these LED lights for applications where a lot of vibration, dust, dirt, dampness and abusive working conditions are encountered. Light Mast: A 44" wide and 2" by 2" by 1/4" thick mounting plate is attached to the upper section of the mast which provides a strong and stable platform for the four LED fixtures. When elevated to its full upright position, the mast can be rotated a full 360¡. By loosening the T-Handle, operators can rotate the mast with easy in either direction. The mast can be positioned in one of four different positions, and locked back in place by re-tightening the T-handle. The mast itself spins freely with easy, and can typically be rotated with a single hand. The LM series of towers are powder coated with glossy blue finish for corrosion resistances and aesthetics. This light mast is mounted to a 14` by 6`, single axle trailer via six 1/2" anchor bolts. The two wheel trailer is equipped with 3,500 lbs axle and leaf springs with 15" trailer tires. The trailer can support and haul an additional 3,500 lbs of equipment. A standard 2" ball coupling, two standard safety chains, and 4-pin flat trailer plug allow for easy hookup and towing. The LM family of telescoping towers feature a proprietary mast guidance system, which provide increased stability during high winds. Four 1,000 lbs hand crank leveling jacks are used for leveling. The jacks can be leveled by hand crank or attachment provided for power drills. These outriggers can be extended 2` out from the side of the trailer for added stability. When lowered to 13.5`, the mast can withstand winds up to 125 mph. Custom builds can be provided for higher wind speed resistance when fully raised. Retractable outriggers with 1,000 lb manual crank jacks and tail lights. Manual 1,000 lb hand crank winch for elevating and folding over the light mast on the LM-20-3S-10TLR-4X400LTL-LED. Mast support bracket for securing the mast boom in the fold-over position during transportation. Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge The entire tower assembly is shipped via common freight carrier or flatbed. Larson Electronics can custom tailor these units to the customer’s requirements with longer sections and larger mounting plates. For example, the LM-40-4S is another model that reaches to a length of 40`, with base section 11.25` in length, lower section 11.25` in length, an upper section 11.25` in length, and a top section 11.75` in length. Larson Electronics can custom build these towers to meet your overall and collapsed height requirements. We also offer a choice of either the manual or electric winches, finishing, and equipped light heads. Winch options include 1,000 lbs hand winches (included standard) or optional electric winches for standard light towers, and heavy duty winches and hoists for high payload units. Powder coating color can be customized (the standard mast is gloss blue). Mast location on the trailer bed can be tongue mounted, front of the trailer bed, or center of the trailer bed. These towers can be fitted with Larson Electronics line of high output light heads, or customize the mast head to meet the mounting requirements for your equipment. Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge Suggested Applications: Temporary lighting, construction sites, and security camera deployment. We can equip this mast with 1000W HID-22-SL-REM or 1500W HID-22-15M-SL-REM Metal Halide lights or a wide variety of high powered LED lights with comparable power, including the LED10WSA-160, LED10WSA-320, LEDP5W-30, LEDP5W-60, and GAU-HB-160LED. Specifications / Additional Information LM-20-3S-10TLR-4X400LTL-LED Trailer Mounted 3-Stage Light Tower Mast/Trailer Summary Light Mast Specs 9` to 20` Light Mast Tower Length: 9` to 20` Steel Construction Mast & Trailer Mast Head Length: 44" Mast - Power Coated Finish Capacity: 150 lbs Trailer - Industrial Paint Finish Materials: Steel Removable Mast Head Finish: Powder Coated - Gloss Blue (4) 1,000lb Retractable Outriggers Operation: (2) 1,000lbs Hand Winches, Electric Optional 125 mph Wind Resistance Cable: 3/16" Galvanized Aircraft Cable Manual or Optional Electric Operation Lamp Specs LED Lamp Head Summary Lamp Type: Cree¨ LED High Output LED Lamps Lamps: (4) 400 Watt LED Fixtures Extreme Area Coverage Total Watts: 1,600 (400W per lamp) Direct Replacement for (4) 800W MH Towers Total Lumens: 216,000 (54,000 per lamp) 1,600W LED compared to 800W MH LED Life Expectancy: 80,000 hours 216,000 Total Lumen Output Controls: Control Box at base of mast Independently Adjustable Light Heads Wiring: 100` 14/3 SOOW Cable w/ Cord Cap Dial-in Adjustability per light head 98% Transmission High Purity PMMA Optics Multiple LED Banks for Heat Dispersion Trailer Specs 130 Lumens Per Watt Efficiency Materials: Steel 70% Lumen Retention after 80,000 Hours Trailer Dimensions: 10`-L x 6`-W trailer bed IP67 Waterproof LED Fixtures Hitch: 2" Ball Coupler 100` 14/3 SOOW Line-In Cable Wiring: 7-Pin Flat Axle: 3,500lb Suspension: 5,400 Lb 4-Leaf Double Eye Springs Outriggers: (4) 1,000 Manual Crack Leveling Jacks - Retractable Wheels: (2) 15" 5x4.5 Steel Rims Tires: ST205/75/D15 H188 Special Orders- Requirements Weight: +-1200 lbs Contact us for special requirements Shipping: Common Freight Phone: 1-214-616-6180 Shipping Dimensions: ~16.5`-L x 4`-W x 5`-H Toll Free: 1-800-369-6671 Shipping Weight: +-1700 lbs Fax: 1-903-498-3364 Options: Length- Mounting-Fixtures/ Call Us for Special Requirements E-mail: [email protected] The customer ships the failed light mast to Larson Electronics at their expense. If the failure is a manufacturer defect, we will repair and/or replace the unit.