Larson Electronics *RENTAL* 580 Watt Solar Light Tower - 30' Light Tower - 10' Trailer - (4) 60 Watt LED Lamps - 80 Amp

Made in the USA The Larson Electronics RNT-SPLT-.58K-80A-LM30-4XWP600E-TLR10 solar powered LED light tower provides a safe and effective way for operators to quickly deploy 240 watts of intense LED illumination to elevations up to thirty feet. This solar light plant features a telescoping light tower that folds over for easy transportation, features a rotating boom that allows for 360¡ of rotation, and a removable mast head for storing the four LED light fixtures when not in use. This unit features two 290 watt solar panels and an 80 amp capacity battery bank. The entire assembly is mounted onto a 10` single axle trailer, allowing operators to transport this solar light tower from location to location. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO LIGHT MASTS OR LIGHT TOWERS* Solar Powered Light Tower: This solar light tower includes two solar panels, solar charging system, battery bank and manual crank up mast mounted on trailer with outriggers. This 0.58KW solar generator system replenishes amp hours of usable battery capacity per day, assuming 5.5 hours of peak charging sunlight. This system delivers 24 volts for lighting mounted atop the 30` telescoping light mast. Light Mast: This telescoping five stage steel light mast from Larson Electronics’ is designed to allow operators to quickly and safely deploy the four LED light heads in locations where this equipment must be elevated to heights up to 30` for effective coverage. This light boom can be extended to 30` above the trailer floor for maximum area coverage, and collapsed to 13.5` for applications where a footprint smaller is required. The tower is constructed of square steel tubing with a base section 6.6` in length and 6" by 6" by 3/16" thick, lower section 6.78` in length and 5" by 5" by 3/16" thick, middle section 6.93` in length and 4" by 4" by 1/8" thick, upper section 7.08` in length and 3" by 3" by 1/8" thick, and top section 7.58` in length and 2" by 2" by 1/8" thick. Each section has a 1`+ overlap. The mast is elevated using an included 1,000lb rated hand winch with 3/16" galvanized steel cable and extended to its full height using a second 1,000 lbs winch. A 44" wide and 2" by 2" by 1/4" thick mounting plate is attached to the upper section of the mast which provides a strong and stable platform for the equipped LED light fixtures. When elevated to its full upright position, the mast can be rotated a full 360¡. By loosening the T-Handle, operators can rotate the mast with easy in either direction. The mast can be positioned in one of four different positions, and locked back in place by re-tightening the T-handle. The mast itself spins freely with easy, and can typically be rotated with a single hand. The LM series of towers are powder coated with glossy blue finish for corrosion resistances and aesthetics. The LM family of telescoping towers feature a proprietary mast guidance system, which provide increased stability during high winds. Four 1,000 lbs hand crank leveling jacks are used for leveling. The jacks can be leveled by hand crank or attachment provided for power drills. These outriggers can be extended 2` out from the side of the trailer for added stability. When lowered to 13.5`, the mast can withstand winds up to 125 mph. Custom builds can be provided for higher wind speed resistance when fully raised. 44" Mast Head for mounting lights and equipment Mast folds over for transportation and when not in use Click Image to Enlarge Click Image to Enlarge LED Light Fixtures: This solar light plant is equipped with four of Larson Electronics` LEDWP-600E high output LED light fixtures. The LEDWP-600E consists of six 10 watt LEDs housed within a waterproof aluminum housing that is powder coated for added durability and resistance to corrosion. The housing incorporates integral cooling fins for efficient heat dissipation and increased LED longevity. The LED lamp assembly is protected by a shatterproof polycarbonate lens which is secured to the housing with a waterproof seal. Mounting hardware for the LEDWP-600E consists of a stainless steel coated bracket and stainless steel screws to provide secure mounting and resistance to rust and corrosion. The mounting assembly provides for 360/180 degrees of rotation and tilt to allow the user to position the unit as desired once mounted. LED Technology: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting. Solar Panel Assembly: This unit is comprised of two 290-watt solar panels, generating a total maximum output of 0.58 KW. The panels are mounted to a stationary assembly. The panels are wired to the solar charger control box which manages the charging system. Solar Charge Controller: In this 24 volt system solar control system, each panel is terminated with a fused combiner box with a single lever action cut-off switch. With the switch set to the ‘on’ position, the combiner box passes power to the 80-amp capacity Outback Extreme charge controller. This solar charge controller system uses the Outback Extreme series since it standard temperature threshold is more than 160 degrees Fahrenheit, due to its integrated heat sink and fan assembly. Oddly enough, most charge controllers aren’t rated past 104 degrees Fahrenheit despite the fact the will always be close to direct sunlight. In the summer time in Texas, our fabrication shop is normally warmer than that, so this solar light tower uses a charge controller that would support the southern heat. We improve on that capability by shading the charge controller and adding additional air flow from the exhaust of a 1400 CFM component cooling system. Images Below Show Light Tower Lowered and Raised to 30ft. Click Images to Enlarge Lamps Off (Ambient Light) (4) 60 Watt LED Lamps Turned On Illuminating Wall 200ft. Away (20,000+sq.ft. area) Area from Above Component Control Center In order to ensure that the 50% threshold on the batteries is controlled, this solar trailer includes a system of min/max voltage sensors and relays that monitor the voltage produced by the batteries and will automatically shut off power distribution when the battery capacity falls below 50%. This protects the batteries from failure. We also include ground fault protection and an Outback Mate 3 monitoring system to track and log all activities related to the charger controller and battery health. In the event there is an issue with the solar trailer, the SD card can be removed from the Mate 3 and sent to Larson Electronics for analysis. All the electrical components, including the combiner panel, charge controller, over/under battery monitoring and ground fault isolation are encapsulated in a NEMA 3R job box that is bolted to the trailer. Since most of these components are not rated for high heat, our component cooling system circulates air within the job box at 1400 CFM when the ambient temperature exceeds 90 degrees Fahrenheit. The component control center also includes a terminal block so that customers can mount additional electronic gear without interfering with the charging systems. The job box that contains the component control system includes locks for security purposes. Trailer Assembly: The entire assembly is mounted to a 10` by 6`, single axle trailer via six 1/2" anchor bolts. The two wheel trailer is equipped with 5,4000 lbs axle and leaf springs with 15" trailer tires. The trailer can support and haul an additional 3,500 lbs of equipment. A standard 2" ball coupling, two standard safety chains, and 7-pin flat trailer plug allow for easy hookup and towing. A rugged and waterproof job box is included, safely secured to the trailer. Specifications / Additional Information SPLT-.58K-80A LM30-4XWP600E-TLR10 Trailer Mounted 3-Stage Light Tower Quick Summary Light Mast Specs 13.5` to 30` Light Mast Tower Length: 13.5` to 30` Steel Construction Mast Head Length: 44" Power Coated Finish Materials: Steel Removable Mast Head Finish: Powder Coated - Gloss Blue (4) 1,000lb Retractable Outriggers Operation: (2) 1,000lbs Hand Winches, Electric Optional 125 mph Wind Resistance Cable: 3/16" Galvanized Aircraft Cable Manual or Optional Electric Operation A-Frame for mounted (2) 290 Watt Solar Panels Solar Specs Fully Solar, No Fuel Needed Panes: (2) 290 Watt panels Waterproof/Vapor Proof Lamps Method of Deployment: Fixed Mount 50,000+ Hour LED Life Panel protection: Fused combiner box Lamps ETL Approved for Wet Locations System Protection: Battery over/under and ground fault IP68 Waterproof Lamps System Voltage: 24 Volts Battery Bank: 2 X 12V 200aH batteries Battery capacity: 400ah total and 200ah usable LED Lamp Specs Lamp Type: CREE LED Total Watts: 240 (60W per lamp) Total Lumens: 21,600 (5400 per lamp) Luminous Efficacy: 90 lm/w LED Life Expectancy: 50,000+ hours Color Temp: 5600K, 4000K, or 3000K Color Rendering Index: 80 Beam Angle: 60¡ Vertical, 75¡ Horizontal Lighting Configuration: Flood Beam Ambient Temp Range: -25¡C to +60¡ Lamp Housing Material: Cast Aluminum Lamp Lens Material: Polycarbonate Trailer Specs Materials: Steel Trailer Dimensions: 10-L` x 6`-W trailer bed Hitch: 2" Ball Coupler Wiring: 7-Pin Flat Axle: 5,400lb Suspension: 5,400 Lb 4-Leaf Double Eye Springs Outriggers: (4) 1,000 Manual Crack Leveling Jacks - Retractable Wheels: (2) 15" 5x4.5 Steel Rims Tires: ST205/75/D15 H188 Special Orders- Requirements Weight: +-1200 lbs Contact us for special requirements Shipping: Common Freight Phone: 1-214-616-6180 Shipping Dimensions: 16.5`-L x 4`-W x 5`-H Toll Free: 1-800-369-6671 Shipping Weight: +-1700 lbs Fax: 1-903-498-3364 Options: Length- Mounting-Fixtures/ Call Us for Special Requirements E-mail: [email protected] Rental Type: Monthly, Weekly, Daily Rentals: In an effort to cut back on contracts and various other paper work, Larson Electronics processes rentals like purchases until the product is returned. (Rent to Own Rates) This means, we will charge the customer for the product total and credit back the difference once the fixture is returned. Weekly and Monthly terms are available. Customer must pay shipping to and from the destination. Please contact us at (903) 498-3363 for further information if required. Rental Prices for the RNT-SPLT-.58K-80A-LM30-4XWP600E-TLR10;;Monthly...$3,355.81 USDWeekly...$2,013.47 USD Subtract rental cost from total cost for the amount that will be credited back to customer upon return of product. Customer can choose to convert their rental to a purchase at any time during the rental period. When returned, deductions will also be made for shipping, repairs, and excessive cleaning, if needed.