Larson Electronics *RENT* 580 Watt Solar Light Tower - 30' Light Tower - 7.5' Trailer - (6) 50 Watt LEDs -Motion Sensor

Made in the USA This unit is for rentals The Larson Electronics RNT-RNT-SPLT-.53K-LM30-6XWP500-MS-TLR7 solar powered LED light tower provides a safe and effective way for operators to quickly deploy 300 watts of intense LED illumination to elevations up to thirty feet. This solar light plant features a telescoping light tower that folds over for easy transportation, features a rotating boom that allows for 360¡ of rotation, and a removable mast head for storing the four LED light fixtures when not in use. This unit features two 265 watt solar panels and a 500 amp capacity battery bank. The entire assembly is mounted onto a 7` single axle trailer, allowing operators to transport this solar light tower from location to location. The RNT-SPLT-.53K-LM30-6XWP500-MS-TLR7 is equipped with a motion sensor for instant illumination whenever motion near the tower is detected. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO LIGHT MASTS OR LIGHT TOWERS* Solar Powered Light Tower: This solar light tower includes two solar panels, solar charging system, battery bank and manual crank up mast mounted on trailer with outriggers. This 0.53KW solar generator system replenishes 350 amp hours of usable battery capacity per day, assuming 5.5 hours of peak charging sunlight. This system delivers 120 volts for lighting mounted atop the 30` telescoping light mast. Light Mast: This telescoping five stage steel light mast from Larson Electronics’ is designed to allow operators to quickly and safely deploy the four LED light heads in locations where this equipment must be elevated to heights up to 30` for effective coverage. This light boom can be extended to 30` above the trailer floor for maximum area coverage, and collapsed to 13.5` for applications where a footprint smaller is required. The tower is constructed of square steel tubing with a base section 6.6` in length and 6" by 6" by 3/16" thick, lower section 6.78` in length and 5" by 5" by 3/16" thick, middle section 6.93` in length and 4" by 4" by 1/8" thick, upper section 7.08` in length and 3" by 3" by 1/8" thick, and top section 7.58` in length and 2" by 2" by 1/8" thick. Each section has a 1`+ overlap.The mast is extended to its full height using an included 1,000lb rated hand winch with 3/16" galvanized steel cable. A 44" wide and 2" by 2" by 1/4" thick mounting plate is attached to the upper section of the mast which provides a strong and stable platform for the equipped LED light fixtures. When elevated to its full upright position, the mast can be rotated a full 360¡. By loosening the T-Handle, operators can rotate the mast with easy in either direction. The mast can be positioned in one of four different positions, and locked back in place by re-tightening the T-handle. The mast itself spins freely with easy, and can typically be rotated with a single hand. The LM series of towers are powder coated with glossy blue finish for corrosion resistances and aesthetics. The LM family of telescoping towers feature a proprietary mast guidance system, which provide increased stability during high winds. Four 1,000 lbs hand crank leveling jacks are used for leveling. The jacks can be leveled by hand crank or attachment provided for power drills. These outriggers can be extended 2` out from the side of the trailer for added stability. When lowered to 13.5`, the mast can withstand winds up to 125 mph. Custom builds can be provided for higher wind speed resistance when fully raised. Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge LED Light Fixtures: This solar light plant is equipped with six of Larson Electronics` LEDWP-500 high output LED light fixtures. The LEDWP-500 consists of four 12.5 watt LEDs housed within a waterproof aluminum housing that is powder coated for added durability and resistance to corrosion. The housing incorporates integral cooling fins for efficient heat dissipation and increased LED longevity. The LED lamp assembly is protected by a shatterproof polycarbonate lens which is secured to the housing with a waterproof seal. Mounting hardware for the LEDWP-500 consists of a stainless steel coated bracket and stainless steel screws to provide secure mounting and resistance to rust and corrosion. The mounting assembly provides for 360/180 degrees of rotation and tilt to allow the user to position the unit as desired once mounted. LED Technology: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting. Lamp Control: Each lamp is grouped into banks of two, allowing operators to power one bank or all six lamps at a single time to fit the required illumination requirements. An equipped dusk-to-dawn day/night sensor allows for anomous operateration of the light configuration set within the the control center. Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge Solar Panel Assembly: This unit is comprised of two 265-watt solar panels, generating a total maximum output of 0.53 KW. The panels are mounted to a stationary assembly. The panels are wired to the solar charger control box which manages the charging system. The two solar panels are mounted to a frame angled at 45¡ to capture the intensity of the sun for optimized light intake. Component Control Center: All the electrical components are encapsulated in a NEMA 3R job box that is bolted to the trailer. Since most of these components are not rated for high heat, our component cooling system circulates air within the job box at 1400 CFM when the ambient temperature exceeds 90 degrees Fahrenheit. The job box that contains the component control system includes locks for security purposes. Motion Sensor: This solar light system is operated via the equipped motion sensor. An internal 3-way switch allows operators to power the lights on, off, or on via the motion sensor. When set to power on via the motion sensor, the lights will automatically turn on whenever motion is detected. With LED technology, there is no warm up period, providing instant high powered illumination. This means that whenever motion is detected, the lights instantly power up and illuminate the area. Trailer Assembly: The entire assembly is mounted to a 7.5` by 7`, single axle trailer via six 1/2" anchor bolts. The two wheel trailer is equipped with 3,500 lbs axle and leaf springs with 15" trailer tires. A standard 2" ball coupling, two standard safety chains, and 7-pin flat trailer plug allow for easy hookup and towing. The trailer tongue can be removed for long term deployment. A rugged and waterproof job box is included, safely secured to the trailer. Four outriggers mounted to the corners of the trailer allow operators to level the trailer, and provide stabilization during deployment. All trailer lighting complies with DOT/FMVSS regulations. Specifications / Additional Information RNT-SPLT-.53K-LM30-6XWP500-MS-TLR7 Trailer Mounted 3-Stage Light Tower w/ Motion Sensor Quick Summary Light Mast Specs 13.5` to 30` Light Mast Tower Length: 13.5` to 30` Steel Construction Mast Head Length: 44" Powder Coated Finish Materials: Steel Removable Mast Head Finish: Powder Coated - Gloss Blue (4) 1,000lb Outriggers Operation: (1) 1,000lbs Hand Winch 125 mph Wind Resistance Cable: 3/16" Galvanized Aircraft Cable Manual or Optional Electric Operation A-Frame for mounted (2) 265 Watt Solar Panels Solar Specs Fully Solar, No Fuel Needed Panes: (2) 265 Watt panels Waterproof/Vapor Proof Lamps Method of Deployment: Fixed Mount 50,000+ Hour LED Life System Voltage: 12 Volts stepped up to 120V Lamps ETL Approved for Wet Locations Battery Bank: (2) 12V 250aH 8D batteries IP68 Waterproof Lamps Battery capacity: 500aH Total / 250aH Usable Motion Sensor LED Lamp Specs Lamp Type: CREE LED Total Watts: 300 (50W per lamp) Total Lumens: 30,000 (5000 per lamp) Luminous Efficacy: 100 lm/w LED Life Expectancy: 50,000+ hours Color Temp: 5600K, 4000K, or 3000K Color Rendering Index: 80 Beam Angle: 60¡ Vertical, 75¡ Horizontal Lighting Configuration: Flood Beam Ambient Temp Range: -25¡C to +60¡ Lamp Housing Material: Cast Aluminum Lamp Lens Material: Polycarbonate Trailer Specs Materials: Steel Trailer Dimensions: 7.5`L` x 7`W trailer bed- 10.75` total length Hitch: 2" Ball Coupler Wiring: 7-Pin Flat Axle: 3,500lb Suspension: 3,500 Lb 4-Leaf Double Eye Springs Outriggers: (4) 1,000 Manual Crack Leveling Jacks Wheels: (2) 15" 5x4.5 Steel Rims Tires: ST205/75/D15 H188 Special Orders- Requirements Weight: +-650 lbs Contact us for special requirements Shipping: Common Freight Phone: 1-214-616-6180 Shipping Dimensions: 8`-L x 8`-W x 12`-H Toll Free: 1-800-369-6671 Shipping Weight: +-650 lbs Fax: 1-903-498-3364 Options: Length- Mounting-Fixtures/ Call Us for Special Requirements E-mail: [email protected] -Scroll Down to Purchase-