Larson Electronics Marine Grade 150 Watt LED Flood Light - 10-32 Volts DC - 14,790 Lumens - 12 Amp Draw

Buy American Compliant The LED-BL-150W LED Boat Light offers high output from a compact form factor and is ideal for use in marine and boating applications. A 14,790 lumen output, 12.5 amp draw, 50,000 hour service life and 10 to 32 volt compatibility provides boaters with a rugged, more powerful, and far more efficient LED alternative to fragile and power hungry halogen lamps. The LED-BL-150W LED boat light from Larson Electronics produces 14,790 lumens of high intensity light while drawing only 150 watts @12.5 amps from a 12 volt electrical system. Thirty CREE XLamp XPG¨ five watt LEDs producing 493 lumens each are arranged in rows and paired with high purity optics to produce a well focused 25 degree spot beam that is ideal for providing far reaching concentrated illumination while still covering a substantial amount of area. We also offer optional floodlight versions with a 60 degree beam spread to provide more light over a larger area nearer the fixture, making flood versions ideal for use as dedicated flood and area lights. These LED boat lights are IP68 rated waterproof, sealed against intrusion by dust and dirt, and very ruggedly constructed to withstand the most demanding marine environments, conditions and applications. LED-BL-150W boat lights offer Pulse Width Modulation control, a small profile, low power requirements, high durability and a versatile mounting system that makes these LED light emitters a superior lighting solution for marine applications where power and reliability is critical. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or “duty cycle” accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each LED based upon the LED’s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 90% capacity without overheating or visible loss of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually on or off. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 50,000 hours. PWM Control: The pulse width modulation drivers in this unit also provide secondary benefits through the ability to automatically monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels across a specific range. These LED-BL-150W series light bars can operate on current ranging from 10 to 32 VDC without any modifications necessary as a result. This ability to sense and adjust input current also provides protection against voltage spikes and drops that can occur in boat electrical systems which would otherwise result in burning up or premature LED failure without it. Durability: As well as unparalleled heat control, this series of LED boat lights from Larson Electronics also offers IP68 waterproof rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40 degrees Celsius to 80 degrees Celsius, are waterproof to three meters, and resist ingress of dust, dirt and humidity. The CREE XLamp XPG¨ LEDs help these units achieve 15.6Grms rated resistance to vibrations and are rated at 70% lumen maintenance after 50,000 hours of use. We recommend these LED lights for use in marine applications where a lot of vibration, salt water, dampness and abusive weather conditions are encountered. Mounting: Each unit is equipped with an innovative trunnion style mounting bracket that allows the light to be attached to flat surfaces and adjusted through 360 degrees of vertical movement. To adjust the unit after mounting, the user simply loosens the thumb screws located on either side of the unit, moves it into the desired position, then retightens the screws. The base of the mounting trunnion is equipped with several machined slots which allow users to utilize existing mounting holes and slide the unit for precise mount positioning. Note: Most Larson Electronics LED-BL-150W, EDPM-5W-30, LEDLB, LEDP3W, LEDP10W, and LED10W series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. Specifications / Additional Information LED-BL-150W LED Boat Light Internal LED Driver Features Lamp Type: CREE XLamp-XPG¨ LED Automatic Current Sensing and Adjusting 10-32VDC Dimensions: 11.69 "-L 7.54"-H 4.94"-D Active Heat Management Watts: 150 Ambient Op Temp -40C to +80C Led Drive %: 90% Voltage: 10 - 32 VDC Lighting Configuration: 25¡ Spot or 60¡ Flood Mounting: Adjustable Trunnion Wiring: Deutsch IPD / LADD DT04-2P connector Amps: 12.5 (on 12 volts) Lumens: 14,790 Special Orders- Requirements LED Light Color: White Contact us for special requirements LED Life Expectancy: 50,000 hours Toll Free: 888-325-4448 Optics Efficiency: 90% Materials: Aluminum Housing, Polycarbonate Lens E-mail: [email protected] Housing Colors: Black Weight: 11.02 Lbs 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement. Scroll Down to Purchase-