Larson Electronics LED Light Emitter on Perko Pole Mount - 21 Watts - 7, 3-Watt LEDs - 12-32 Volts - 675'L X 45'W Spot

Buy American Compliant The Larson Electronics LEDLB-21-S LED Light Bar with Perko Post (Stanchion) Mount. This unit offers high light output in a light weight, durable, low profile housing. This light produces a very tight spot pattern, can run on any 12 Volt source and provides a rugged lighting solution ideal for use in marine environments. The LEDLB-21-S LED light emitter from Larson Electronics produces a 675` long by 45` wide light beam with 1750 lumens of bright light while drawing only 21 watts @1.6 amps from a 12 volt electrical system. Seven Edison Edixeon¨ Emitters containing CREE EZBright¨ three watt LEDs producing 180 lumens each are paired with high purity 10 degree optics to produce a tightly focused spot beam with limited spread or light spillage. Unlike other LED spots, this unit is not a wide spot. The beam on this fixture is so tight, it resembles the pattern of an HID spot (not distance-wise). This fixture is ideal for anyone who is looking for a tight spot light that offers a outstanding life hours of 50,000+. We also offer optional floodlight versions with 35 degree optics to produce a wider beam spread approximately 80` long by 70` feet wide, making flood versions ideal for use as work and area lights. These LED light bars are IP67 rated and waterproof to one meter, sealed against intrusion by dust and dirt and ruggedly constructed to withstand demanding environments and applications. The entire Larson Electronics LEDLB series are constructed of extruded aluminum and feature rubber isolated mounts and unbreakable polycarbonate lenses to provide durability and resistance to vibrations, impacts, waves, hard rains, sand and high winds. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. As a result, many manufacturers reduce the output of their LEDs to reduce the amount of heat produced. These LED light bars utilize an extruded aluminum housing that incorporates an advanced heat radiating fin design which dissipates heat efficiently to produce the maximum amount of power and longevity from the integrated Edison Edixeon¨ Emitters. The end result is more light and longer LED life with higher average lumen maintenance after 50,000 hours. Voltage Control: These units are able to monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels. These LEDLB series light bars can operate on current ranging from 9 to 42 VDC without any modifications necessary as a result. This multi-voltage capability makes these units ideal for mobile and stand alone applications such as those found on boats, heavy equipment and vehicles where power systems don’t always operate with 12 volts and external generators, transformers or inverters are impractical. LEDLB-21-S 35¡ Flood Beam(Opt) LEDLB-21-S 10¡ Spot Beam(Stnd) Durability: The LEDLB series of LED light bars from Larson Electronics offer IP67 rated construction that is designed to withstand tough environmental and operating conditions yet are lighter and more compact than our extreme duty E series light bars. These units can operate in temperatures ranging from -40 degrees Celsius to 85 degrees Celsius, are waterproof to one meter and resist ingress of dust, dirt and humidity. The housings are formed from extruded aluminum, the hardware is stainless steel and the lenses are unbreakable polycarbonate. The Edixeon¨ LEDs offer inherent LED resistance to shocks and vibrations, contributing to these units 15.6Grms rating of vibration tolerance. These LEDLB series light bars are ideal for use in marine environments as well as industrial and commercial settings. MOUNTING POLE (STANCHION POST):- Pole (stanchion) mount enables light to be installed and/or removed and stored. Included running lights are always on when mount is receiving power.- We offer 6 inch, 12 inch, 24 inch and 42 inch pole lengths- 2 gold plated connectors imbedded in nlylon base bring power from Perko socket- Locking nylon collar twists into place- Standard Perko socket, commonly installed on many boats, accepts stanchion post mount. Sliding door Perko socket included with installation template. Click here for Instructions on the Perko Mount Note: Most Larson Electronics LEDLB, LEDP3W, LEDP10W, and LED10W series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. Specifications / Additional Information LEDLB-21-S LED Light Bar LEDLB LED Features LEDs: 7 Edixeon¨ 3 Watt LED Emitters Edixeon¨ 3 Watt LED Emitters Dimensions: 4.5"- OD 4.7"-H 3.25"-D LEDs Driven At 80% Watts: 21 -40 C~ +80C Operating Temp Range Voltage: 12-32 VDC 70% Lumen Retention @65,000 hours Weight: 4 Lbs IP67 Rated Waterproof to 1 meter Lighting Configuration: 10¡ Spot or 35¡ Flood Mounting: Perko Mount (Stanchion) Wiring: Deutsch IPD / LADD DT04-2P connector Amps: 1.6 (on 12 volts) .6 (on 24 volts) Lumens: 1750 Special Orders- Requirements LED Light Color: 6000K Contact us for special requirements LED Life Expectancy: 50,000 hours Toll Free: 888-325-4448 Optics Efficiency: 90% Materials: Aluminum Housing, Polycarbonate Lens E-mail: [email protected] Housing Colors: Black or White CE Certified 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement. Scroll Down to Purchase-