Larson Electronics Explosion Proof Fluorescent Lights - Paint Booths, Rigs - 4', 3 Lamp Fixture - Bi-Axial Bulb Design

Made in the USAThe Larson Electronics EPL-48-1.5L-BX Explosion Proof Three Bi-Axial Bulb Fluorescent Light Fixture is NRTL Listed for United States and Canada, rated Class I Divisions 1 & 2 and Class II Divisions 1 & 2 carries a T6 temperature rating and ideal for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist.The EPL-48-1.5L-BX fixture is a 4 foot long, 3 lamp, Class I Divisions 1 & 2 and Class II Divisions 1 & 2 explosion proof fluorescent light which is also approved for use in paint spray booth applications. This T6 temperature rated fixture comes standard with three Bi-Axial 40 watt compact fluorescent bulbs which produce a combined 120 watts of illumination. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. The EPL-48-1.5L-BX provides operators in hazardous locations with an effective explosion proof lighting solution that provides more light than similar two bulb units.Click Image to EnlargeClick Image to EnlargeClick Image to Enlarge This Biaxial Lamp fixture is multi-voltage capable and can operate on voltages ranging through 100/120 Volts 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ, and 277 Volts 60 HZ with 347 Volt and 480 Volt versions available upon request.Mounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting configurations.Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2" NPT junction box on one end, and a 1/2" NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture`s lead wires, completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs.Made in USA Quality1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Larger ballast box accommodates High Output lamp ballasts. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection. Specifications / Additional Information EPL-48-1.5L-BX RatingsNRTL Listed for United States & Canada Class I Division 1 Groups C and DLamp Type: Fluorescent Class I Division 2 Groups A, B, C & DDimensions: W-11.25" L-52" H-8.5 " NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Weight: 58 Lbs NRTL Certified to UL 844, 924Voltage:120V-60hz 220V-50hz 240V-60hz 277V-60hz NRTL Certified to UL 1598 Marine TypeOptional Voltages: 347 Volt and 480 Volt Class II Divisions 1 & 2 Groups E, F & GTotal Watts: 120 watts Certified Canadian StandardsTotal Lumens 10,500 Listed for Paint Spray BoothsLuminous Efficacy: 88 Lm/W California Title 24 CompliantLED Lamp Life Expectancy: 20,000+ Hours Color Temp: 4000K Beam Angle: 150¡ Ambient Operating Temp Range:-30¡C to +70¡C Operating Temp Range: T6 rated Special Orders- RequirementsMounting: Bracket Standard - Pendant Optional Contact us for special requirementsWiring Hub: 1/2 Inch Threaded Toll Free: 888-325-4448Intl: 1-903-270-1187U.L Approval: U.S Certificate Canada Certificate E-mail: [email protected]