Larson Electronics Explosion Proof Emergency LED light - 4 foot 2 lamp - 2 Hour Backup Ballast - C1D1 LED Light

Made in the USA The Larson Electronics EPL-2XEMG-48-2L-LED Explosion Proof LED Light Fixture is U.S./Canada UL Listed Class 1 Division 1 &2 and Class 2 Division 1 and 2 for areas where flammable chemical/petrochemical vapors exist or have the potential to exist. This explosion proof LED light has a T-6 temperature rating and a carries a paint spray booth light certification as well. The EPL-2XEMG-48-2L-LED is equipped with Larson Electronics’s specially designed LED T-series bulbs which produce 15% more foot candles of illumination at 8 feet as compared to standard T8 lamps when measured with an Extech light meter. Our LED-T series bulbs are visibly brighter than standard T8s and have consistently surprised many of our customers with their unexpectedly high light output levels. We have replaced two 8 foot dual lamp T8 fixtures in our own facility with our LED T series lamps and produced more illumination in the work area with only one 2 lamp 4 foot long LED fixture. We now offer our second generation LED tube lamps with this fixture which have increased this hazardous location light’s performance. With an integrated emergency ballast, this explosion proof LED light will continue to operate one bulb for two hours at 2750 lumens once the main electrical power to the light is severed. Once standard electrical power is restored, the emergency battery pack will be recharged. We have eliminated the ballast box normally associated with fluorescent fixtures which reduces overall weight and creates a slimmer unit profile. There is no ballast in this unit and the included LEDT-24W LED lamps have a 50,000+ hour service life, both of which result in extreme efficiency and greatly reduced maintenance costs. The solid state design of the LED lamps give this fixture superior resistance to damage from vibration, extremes in temperature and a lamp service life over twice that of standard T8 bulbs. The 24 watt LED lamps produce more illumination than standard T8 bulbs, but draw only 3/4 of current. A standard EPL-EMG-48-2L-T8 explosion proof fluorescent light, with a combined total of 64 watts, draws 0.54 amps @ 120 volts. This LED version of the same light, with a total of 48 watts, draws only 0.4 amps. The EPL-2XEMG-48-2L-LED is multi-voltage (universal) and operates on any voltage from 120V to 277V AC 50/60hz. We also make a 12/24VDC version for low voltage applications (-LV suffix) for DC power.Our EPL-2XEMG-48-2L-LED LED light fixture is U.S. and Canada U.L. approved for use in paint spray booths. Please note, according to the NEC, using threaded rigid pipe does not require additional seal offs with this fixture. An EYM and seal off is necessary for flex conduit or other non-rigid pipe implementations.Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown below illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fixture. Additional mounting options:Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit).Made in USA QualitySuperior LED Benefits1. Each unit dielectrically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy4. No ballast box. No ballast to replace. We simply run the black wire to one end of the bulb and white wire to the other. 5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection. 1. 50,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces energy use and prolongs life-spans of peripheral cooling units (A/C, refrigeration)5. 100% recyclable.6. No toxins-lead, mercury.7. No UV light, infrared radiation or CO2 emissions.8. Qualifies buildings for LEED and other sustainable business certifications.9. Bright, even light maintains consistent color over time.10. Instant on/off – No flickering, delays or buzzing. 11. Very good color rendering.12. Vibration/impact resistant.13. Significantly cooler operation.14. Less frequent outages, higher output improves workplace safety.Specifications / Additional Information EPL-2XEMG-48-2L-LED Explosion ProofU.L. RatingsUL Listing: United States - CanadaClass 1 Division 1, Groups C and D T6Dimensions: W-11.25" L-52" H-8.5 "Class 1 Division 2, Group A,B,C,DWeight: 45 Lbs UL 595 Outdoor Marine Type (Saltwater)Total Watts: 48 watts UL 844, 924Voltage: Universal 120-277VAC 50/60 hzUL 1598 Marine TypeLow Voltage (Optional): 12/24 Dc powerClass II, Division 1 - 2, Groups E,F,GLED Lamp Life Expectancy: 50,000+ HoursUL Certified Canadian StandardsEfficiency: 90 Lumens per WattUL listed for Paint Spray Booth OperationCalifornia Title 24 CompliantOperating Temp Range: -30 C to 70 CBeam Angle: 150 degreesSpecial Orders- RequirementsColor Temp: 5300KContact us for special requirements Mounting: Surface Standard - Pendant OptionalWiring Hub: 1/2 inch threadedToll Free: 888-325-4448Warranty: YES- 5 Years*Intl: 1-903-270-1187U.L Approval: U.S Certificate Canada CertificateE-mail: [email protected]*5 year warranty replacement on this LED light (or LED bulbs for light fixtures with removable LED bulbs). After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement.Scroll Down to Purchas