Larson Electronics 72W Surface Mount Explosion Proof Fluorescent Light Fixture - Paint Booth Rated - 6700 Lumens - 2 La

Made in the USAThe Larson Electronics EPL-48-2L-INTL-36WT8 Explosion Proof Fluorescent Light Fixture is NRTL Listed for United States and Canada, and rated Class 1 Division 1 and Class 1 Division 2 for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist. The unit carries a T6 temperature rating and is also approved for Paint Spray Booths.The EPL-48-2L-INTL-36WT8 fixture is a 4 foot long, 2 lamp, Class 1 Division 1 and Class 2 Division 1 & 2 explosion proof fluorescent light which is also approved for use in paint spray booth applications. This T6 temperature rated fixture comes standard with two 36 watt T8 fluorescent lamps. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish.This fixture is multi-voltage capable and is available with a variety of lamp options. The EPL-48-2L-INTL-36WT8 provides operators in hazardous locations with a reliable and affordable lighting solution that provides the best explosion proof protection available without sacrificing light quality or fixture durability.Click Image to EnlargeClick Image to EnlargeClick Image to Enlarge T8 LEDWattage 36 watts 48 wattsAmp Draw @ 120V AC 0.3 amps 0.4 ampsAmp Draw @ 277V AC 0.13 amps 0.18 ampsAmp Draw @ 12V DC 3 amps 4 ampsAmp Draw @ 24V DC 1.5 amps 2 ampsLamp Life Expectancy 24,000 hours 50,000 hoursColor Temperature 4100K 5300KOperation cost per year(8hs/day @ 11c/kWh) $11.56 $15.42Click here to see the LED version of this fixtureMounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting configurations.Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2" NPT junction box on one end, and a 1/2" NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture`s lead wires, completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.Made in USA Quality Lamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Larger ballast box accommodates High Output lamp ballasts. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the "tap and knock off" method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.F36-T8/841 - 36 watt, 3350 lumens per bulb, 24,000 hours life, 4100 Kelvin color (Suffix -T8) Specifications / Additional Information EPL-48-2L-INTL-36WT8 Explosion Proof Fluorescent Light Fixture Ratings/ApprovalsNRTL Listed for United States - Canada Class I Division 1, Groups C and D T6Dimensions: W-11.25" x L-52" x H-8.5 " Class I Division 2, Group A,B,C,DWeight: 65 Lbs Class II, Division 1 & 2, Groups E,F,GVoltage: Universal 120-277VAC 50/60 Hz NRTL Certified to UL 595 Marine Type (Saltwater)Total Watts: 72W NRTL Certified to UL 844Total Lumens: 6,700 NRTL Certified to UL 1598 Marine TypeLamp Life Expectancy (Hrs): 24,000 hours Certified Canadian StandardsLuminous Efficiency (Lm/W): 186.1 Lm/w Listed for Paint Spray BoothsColor Temp: 4100K ABS CertifiedBeam Angle: 150¡ California Title 24 CompliantAmbient Operating Temp Range: -20¡C to +70¡C IP67 Rated - WaterproofOperating Temp Rating: T6 Rated T6 Temperature RatingMinimum Operating Temp: -30¡C NEMA 4XMaximum Case Temp: +90¡C Approved for Confined SparesHousing Material: Cast Aluminum End Caps, Aluminum Reflectors - Copper Free Lens Material: Hardened Borosilicate Glass Tubes Special Orders- RequirementsGasket Material: Buna Rubber O-Rings Contact us for special requirementsMounting: Surface Standard - Pendant Optional Phone: 1-214-616-6180Wiring Hub: 1/2" NPT Toll Free: 888-325-4448Fax: 1-903-498-3364?E-mail: [email protected]*Temperatures above +65¡ C will diminish ballast life from 5 years to 3 years