Larson Electronics 1920 Watt High Output LED Light Plant - 6KW Genset - 19.5' Pneumatic Mast - 4X1000 Watt MH Alternate

Made in the USA The WCDE-6-PLM-19.5-5.5-4X400LTL-LED 1600 Watt LED Light Plant from Larson Electronics is a high power lighting package powered by a 6kw brushless water cooled diesel generator. This 19.5` pneumatic tower is mounted to a 6.5` by 5` single axle trailer and folds over for transportation and when not in use. The four 400 watt LED lamps included with this unit produce a combined total of 216,000 lumens and is a direct replacement for 800 watt metal halide light plants. This trailed mounted light tower and diesel generator set comes equipped with a 4 gallon fuel tank that will run continuously without refueling for up to 7 hours consecutive hours. The WCDE-6-PLM-19.5-5.5-4X400LTL-LED Light Plant is a self contained, towable, high power light tower package. This unit contains a water cooled diesel engine powering a 6KW, which supplies the current for four 400 watt LED lights producing 54,000 lumens each, for a combined total of 216,000 lumens of light. This unit can run uninterrupted for up to 7 continuous hours without refueling and includes a pneumatic telescoping light mast which can elevate the four high output LED lamps to a height of 23.5 feet above ground level. This mobile floodlight package is ideal for large scale event illumination, construction, mining, industrial operations, and anywhere a mobile full power lighting system capable of extended operation is needed. Larson Electronics`s’ WCDE-6-PLM-19.5-5.5-4X400LTL-LED 1,600 watt trailer mounted telescoping pneumatic light tower allows operators to quickly and safely deploy illumination in locations where elevated illumination is needed for maximum area coverage. This six section pneumatic light boom can be extended to 19.5` above the trailer bed for maximum area coverage and collapsed to 5.5` above the trailer bed and folded over for transport or when not in use. The tower is constructed of heat treated aluminum round tubing with six sections measuring. The mast is stood upright via a manual hand crank winch, and extended to its full height using the equipped 230V AC air compressor. Lights: The lighting system on this unit is comprised of four our of GAU-LTL-400W-LED 400 watt LED lamps producing 54,000 lumens of light each attached to the end of the telescoping pneumatic light boom. These floodlights produce a wide flood light pattern with a combined total of 1,600 watts and 216,000 lumens of light. The GAU-LTL-400W-LED lights are ideal replacements for fragile and hot running 800 watt metal halide lamps, offering increased durability, longer lamp life, and lower power consumption. The entire lighting assembly is connected to the power source via a 4-switch control box. Each light head is on an individual circuit and can be powered on or off independently of the other light fixtures. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units feature individual heat sinks per bank of six LEDs to control heat buildup rather than utilizing a single housing to dissipate heat. This allows for more thorough cooling of the LEDs for extended operating periods. This allows the LEDs to be driven at up to 90% capacity without overheating or visible loss of light output. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 80,000 hours. In addition, should an LED failure occur, these LED flood lights are field serviceable. Each bank of six LEDs can be replaced with the fixture installed. This allows for the tower to stay in operation until repairs can take place, and eliminates the need to remove and disassemble the entire fixture for repairs. Durability: As well as unparalleled heat control, the GAU-LTL-400W-LED series of LED lights from Larson Electronics also offer IP67 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40¡ Celsius to +80¡ Celsius, are waterproof, and resist ingress of dust, dirt and humidity. The housings are formed from die cast aluminum and the optics are high transmission PMMA with 98% light transmittance. The Cree¨ LEDs help these units achieve resistance to vibrations and are rated at 70% lumen maintenance after 80,0000 hours of use. We use these LED lights for applications where a lot of vibration, dust, dirt, dampness and abusive working conditions are encountered. Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting. The above image shows the comparison of the traditional 4000 watt metal halide light plant (left) to the WCDE-6-PLM-19.5-5.5-4X400LTL-LED LED light plant. The area being illuminated by each tower is 300` in length and 250` in width. Unlike the metal halide light plant, there are no hot spots with the LED plant. This high output LED light plant provides an even beam spread over the targeted work area without overcast, glare, light spillage, and wasted illumination. Color rendering is also increased with LED light plants, providing a more realistic night vision that more closely resembles natural daylight illumination. Genset: The WCDE-6-PLM-19.5-5.5-4X400LTL-LED mobile light tower includes a ultra silent genset that houses a 10HP diesel engine powering the 6KW 120/240V brushless generator. This genset is air cooled and features a single phase generator with electric start ignition. A self contained 4 gallon internal fuel tank sits inside the genset and is equipped with an electric fuel delivery system. This genset features key operated electric starting, a twelve volt electrical system, air cooling, replaceable dry element air cleaner, and a full enclosure for safe operation and protection against the elements. This engine also features cold weather options to improve performance under cold weather conditions. Telescoping Boom: The aluminum pneumatic is stood upright via a 1,000lb manual hand crack winch, and the mast reaches 19.5 foot in height via the use of a 220 volt air compressor. The compressor is equipped with a pressure switch that maintains the pressure within the mast. Once the mast is deployed from the component control center, its operation is automated. The air compressor will turn on briefly when the pressure in the mast falls below the fully inflated threshold. In normal operation, the air compressor may turn on once every few days for about 5 minutes to top off the mast. When it is time to take the mast down for transport, the operator simply release the pressure switch and the mast will slowly release pressure and lower to its collapsed height of 5.5 feet. At the top of the mast, we include a removable mounting bracket that is 4 foot in length and supports the four LED light fixtures. The air operation of the pneumatic mast provides operators with convenient and easy deployment, unlike traditional light plants with manual crank winches or time consuming and noisy electric winches. The mast goes from its fully collapsed position to fully extended height of 19.5` in less than 60 seconds. All wiring is internally ran, so there are no pinch points and no messy wiring harnesses to get in the way during deployment of the pneumatic mast. Housing: All of the operating components are housed with protective compartments designed to provide protection against the elements while providing easy access for operation and servicing. Hinged doors provide access to interior control and operating systems while latches provide secure closing while the unit is in use or transport. All controls, systems and operating equipment is labeled with the proper safety decals and notifications. Trailer: The entire system is mounted onto a two wheel, single axle trailer constructed of tube steel and 1/8" steel plate trailer bed. The trailer is approximately 6.5 feet long and 5 feet wide. Each axle is rated at 3,500 lbs and equipped with electric brakes and ST205/75/D15 H188 tubeless tires and steel wheels. The trailer is equipped with a removable tongue for storage and transport purposes. For an additional charge, we offer removable wheels in addition to the removable tongue for extra security. A single 3,500 lbs rated tongue jack provides a stable connect-disconnect platform as well as additional stability during tower deployment. The trailer is finished in industrial grade paint for protection against rust and corrosion and provides an attractive finish. The five 3,500 lb integrated outriggers can be slid out from the frame and pinned into place. A standard crank style support leg can be used to secure each outrigger to the ground. The outrigger feet are over-sized and equipped with through holes for additional ground anchoring mechanisms. This light tower can withstand winds up to 60 MPH when properly deployed. We can equip this mast with 1000W or 1500W Metal Halide lights or a wide variety of high powered LED lights with comparable power. We also offer a choice of either the manual 1,000 lbs hand winches included standard or optional electric winches. Call us at 1-800-369-6671 or contact us at [email protected] to discuss any special custom ordering requirements. Suggested Applications: Construction sites, event lighting, emergency services, highway projects, industrial plants, mining and excavation and anywhere a mobile light source with large area coverage capability is needed. Specifications / Additional Information WCDE-6-PLM-19.5-5.5-4X400LTL-LED LED Light Plant Features / Quick Summary Genset Specs: 6KW Brushless Genset Engine: 418cc 10 HP diesel engine 4 Gallon Internal Fuel Cell Engine Type: Vertical, air-cooled, 4-cycle diesel engine Cold Weather Package Factory Installed No. of Cylinders: 2 Up to 7 Hour Continuous Operation Generator: 6KW 2-Pole Brushless 5.5` to 19.5` Light Mast Voltage: 120/240V Single Phase - 12V DC Pneumatic Aluminum Mast Fuel Cell Capacity: 4 Gallons Electric Air Powered Mast Operation Fuel Delivery: Electric 1/3 HP Electric Air Compressor Cold Weather Package: Yes - Factory Included - Glowplugs High Output LED Lamps Extreme Area Coverage Light Mast Specs: Direct Replacement for (4) 1000W MH Light Plants Mast Type: Pneumatic 1,600W LED compared to 4000W MH Length: 5.5` to 19.5` 216,000 Total Lumen Output Mast Head: 56"-L x 30"-H x 4"-D Independently Adjustable Light Heads Capacity: 150 lbs Dial-in Adjustability per light head Materials:Heat Treated 6063B/T5 Aluminum 98% Transmission High Purity PMMA Optics Operation: Pneumatic via Electric Air Compressor / Manual Crank Winch Multiple LED Banks for Heat Dispersion Air Compressor: 1/3 HP 220V DC Electric Air Compressor 135 Lumens Per Watt Efficiency Stages: Six 70% Lumen Retention after 80,000 Hours Switched Breaker System per Lamp Head LED Light Specs: Removable Mast Head & Light Fixtures Lamp Type: Cree¨ LED IP67 Waterproof LED Fixtures Total Watts: 1,600 (400W per lamp) All Equipment Mounted on a 6.5` x 5` Trailer Total Lumens: 216,000 (54,000 per lamp) Steel Trailer w/ Industrial Grade Paint Finish Luminous Efficiency: 135 lm/w Removable Trailer Tongue for Storage/Transport LED Color Temperature: Cool White - 5500-6500K 7-Point Outrigger System LED Life Expectancy: 80,000 hours 1,000 lb Leveling Jacks Optics Efficiency: 98% - PMMA High Transmittance Optics Led Drive %: 90% Power Factor: >97% Mounting: Flat Surface Trunnion Mount U-Bracket Materials: Die Cast Aluminum Housing, Acrylic Optics Housing Color: Natural Aluminum Ambient Temperature Range: -40¡C to +80¡C Waterproof Rating: IP67 Trailer Specs Materials: Steel Trailer Dimensions: 6.5`-L x 5`-W Trailer Bed Trailer Bed Height: 23" Above Ground Total Collapsed Height (w/o Lights): Total Collapsed Height (w/ Lights): Total Extended Height (w/o Lights): 21`-3" Total Extended Height (w/ Lights): 23`-6" Footprint: 14.62"-L x 9.47`-W w/ Outriggers Extended Hitch: 2" Ball Coupler Tongue: Removable (for transit/storage only) Finish: Industrial Grade Paint Wiring: 7-Pin Flat Trailer Plug Axle: (1) 3,500 lbs Suspension: 3,500 lbs Double Eye Leaf Springs Outriggers: (2) 48" & (4) 24" Retractable Outriggers w/ 1,000 lbs Manual Leveling Jacks Wheels: (2) 15" 5x4.5 Steel Rims Tires: ST205/75/D15 H188 Special Orders- Requirements Contact us for special requirements Mounting: Towable Trailer, 3,500 lbs Axle, 2” Ball Coupler Toll Free:1-800-369-6671 Dry Weight: Intl:1-903-270-1187 Run Time: Up To 7 Hours on Single Tank of Fuel E-mail: [email protected] Down to Purchase-