SensorWorx SWX-100-1 SERIES Low Voltage
The Sensors detect movement in the infrared energy that radiates from occupants as they move within the devices field-of-view. Once occupancy is identified, the sensor signals a connected power/relay pack to switch on the connected lighting. All units can also be configured to operate in Vacancy Mode (e.g., require lights be manually switched on). Once lights are on and if equipped with passive dual technology (PIR/Acoustic), the unitÕs microphone is enabled to further enhance detection. An internal timer is set to keep lights on during brief periods of inactivity, and is reset every time occupancy is signaled by either the passive infrared or acoustic detection technologies. Ambient daylight detection can also be enabled in equipped units so that lights are held off in rooms with sufficient light contribution from windows or skylights. A wall switch sensor is typically used in a small room or enclosed space. A Passive Infrared (PIR) only sensor is sufficient for spaces where line of site is maintained and occupants are periodically moving (e.g., copy rooms, storage rooms). Dual technology sensors are necessary where occupants may be partially blocked from the sensorÕs direct view or where they may be stationary (e.g., private offices or restrooms with stalls). Enclosure is 25-40% Shallower than Unique Bat-Wing Shaped Lens Provides Modern Look and Intuitive Wall-To-Wall Passive Infrared Passive Acoustic Detection (Optional) Ð 100% Passive Detection Methods Ð Configurable Sensor Settings Including Time Blue Locator LED when Lights are Off Optional Wiring Connections for Multi-way This wall switch sensor can be used to meet many requirements of ASHRAE 90.1, IECC, and Title 24. 30Ó to 48Ó (0.76 Ð 1.22 m) recommended mounting height Wall to wall (~180 degree) coverage Small motion (e.g., hand movement) detection up to 20 ft (6.10 m), ~625 ft Large motion (e.g., walking) detection greater than 36 ft (10.97 m), ~ 2025 ft Overlapping acoustic detection of occupants over entire coverage area Advanced signal processing filters out nuisance noises while not effecting overall sensitivity Unit works both in installations where Neutral connection is available as well as installations where only Ground connection is present The unitÕs two black wires are interchangeable (e.g., one connects to line power, one connects to load) *WALLPLATE NOT INCLUDED
The Sensors detect movement in the infrared energy that radiates from occupants as they move within the devices field-of-view. Once occupancy is identified, the sensor signals a connected power/relay pack to switch on the connected lighting. All units can also be configured to operate in Vacancy Mode (e.g., require lights be manually switched on). Once lights are on and if equipped with passive dual technology (PIR/Acoustic), the unitÕs microphone is enabled to further enhance detection. An internal timer is set to keep lights on during brief periods of inactivity, and is reset every time occupancy is signaled by either the passive infrared or acoustic detection technologies. Ambient daylight detection can also be enabled in equipped units so that lights are held off in rooms with sufficient light contribution from windows or skylights. A wall switch sensor is typically used in a small room or enclosed space. A Passive Infrared (PIR) only sensor is sufficient for spaces where line of site is maintained and occupants are periodically moving (e.g., copy rooms, storage rooms). Dual technology sensors are necessary where occupants may be partially blocked from the sensorÕs direct view or where they may be stationary (e.g., private offices or restrooms with stalls). Enclosure is 25-40% Shallower than Unique Bat-Wing Shaped Lens Provides Modern Look and Intuitive Wall-To-Wall Passive Infrared Passive Acoustic Detection (Optional) Ð 100% Passive Detection Methods Ð Configurable Sensor Settings Including Time Blue Locator LED when Lights are Off Optional Wiring Connections for Multi-way This wall switch sensor can be used to meet many requirements of ASHRAE 90.1, IECC, and Title 24. 30Ó to 48Ó (0.76 Ð 1.22 m) recommended mounting height Wall to wall (~180 degree) coverage Small motion (e.g., hand movement) detection up to 20 ft (6.10 m), ~625 ft Large motion (e.g., walking) detection greater than 36 ft (10.97 m), ~ 2025 ft Overlapping acoustic detection of occupants over entire coverage area Advanced signal processing filters out nuisance noises while not effecting overall sensitivity Unit works both in installations where Neutral connection is available as well as installations where only Ground connection is present The unitÕs two black wires are interchangeable (e.g., one connects to line power, one connects to load) *WALLPLATE NOT INCLUDED
