The Larson Electronics Solar Powered Hazardous Location LED Light is an ideal lighting solution for remote areas and standalone applications where connection to external power is either impractical or unavailable. This hazardous location LED light is powered by two 8aH sealed lead acid batteries that are recharged by a 30 watt solar panel. Light output comes from a 10 watt LED lamp that produces 1050 lumens. This solar panel can be equipped with either a dusk to dawn day/night sensor, a motion sensor, an on/off switch, or configured to run 24/7. The day/night sensor is programmed to activate the solar panel in the evening and to shut it off during the day. The motion sensor will activate the panel upon detecting motion. The on/off switch will activate and shut off the solar panel according to the operator`s preferences. The light runs for 12 hours when the battery is fully charged. Charging time for the sealed lead acid batteries is 5 hours when exposed to direct sunlight. Indirect sunlight will extend the charge time. As with all solar powered equipment, charging time is affected by the amount of available ambient light. When ambient light levels drop below a certain level, such as on cloudy days, the unit will not recharge as quickly. The battery pack is contained within the solar panel, not the light. The illumination produced by the explosion proof LED light will cover an area approximately 55 long x 55 wide when mounted 12 feet from the ground. Mounting options include ceiling, wall and pendant for the lamp fixture and flat surface or round/square pole mounting such as on utility poles or structure supports for the solar panel.Surface MountPendant MountStanchion MountMountingRound PoleSquare PoleSurfaceThis hazardous area light (Lamp Fixture only) is ETL approved Class 1 Division 2, Groups A, B, C and D. These lights are also compliant with NEMA 4X standards and marine-rated for use in salt water environments. The high power LED cluster is protected by an internal cooling fin array that reduces heat build for longer LED life and higher light output consistency.This hazardous location LED light contains an LED bulb that can serve to illuminate small work areas or draw attention to towers and other structures from a distance. This C1D2 LED light can be configured for steady burn or strobing applications. The lamp housing is waterproof, constructed of corrosion and chemical resistant GE Lexan polycarbonate with Pyrex globe, USCG accepted, and NEMA 4X compliant and suitable for hose-down areas. The lamp is shown with a wall mount configuration, but can be configured with a pendant or ceiling mount as well. The fixture ships with 30 feet of SOOW cable and custom lengths are available upon request. Please contact us for special requirements.NOTE: Larson Electronics has further upgraded the options available with this light. We expect the light to be mounted separately from the panel. This means the solar panel can be mounted in direct sunlight (not in the hazardous area) while the light is mounted in a hazardous area workspace. Standard installation for explosion proof lighting, including threaded rigid pipe to the LED light fixture and appropriate seal-offs, etc. are required. Specifications / Additional Information HAL-LED-SOL12 Solar Powered Hazardous Location Light UL Ratings For Light Operation: Automatic/Manual Class 1 Div 2 -Groups A, B, C, D Solar Panel Dimensions: W-11 3/8" L-15 3/4" D-1" UL 595: Marine Outside Type Lamp Dimensions: 5.94"-Diameter, 9.6" Height UL 844: C1D2 hazardous Location Panel Watts:30 UL Listed to CSA 22.2-137 Lamp Watts: 10W (7W for colored or strobe) NEMA 4X Lamp Configuration: Steady burn OR strobing beacon -29¡C to 40¡C Operating Temp Charging Time: 5 Hours USCG Approved Lumens: 1050 Runtime: 12 Hours Lamp Mounting: Wall, ceiling or pendant Panel Mounting: Flat Surface / Round/Square Pole Special Orders-Special Requirements Battery: (2) 8aH sealed lead acid batteries Contact us for special requirements Charging Time: 5 Hours Phone: 1-903-270-1187 Wiring: 30 feet of SOOW cord, Custom lengths Available on request. Toll Free: 888-325-4448 Lamp Wiring Hub: 3/4" Threaded Fax: 1-903-498-3364 Lamp Temp Rating: T6 - All Voltage and Temperature Ranges E-mail: [email protected] Click here to learn more about National Electrical Code Hazardous Location Classifications Scroll Down to Purchase-
Larson Electronics Solar Power LED Hazardous Location Light - Class 1 Division 2 - Strobe or Steady Burn - 30 ft SEOOW
Larson Electronics
- SKU:
- HAL-LED-SOL12
- Weight:
- 0.00 LBS