Larson Electronics Low Profile Explosion Proof Fluorescent Light - Emergency Battery Backup - 20,000 Lumens

Made in the USAThe Larson Electronics EPL-EMG-48-216 Explosion Proof Fluorescent Light Fixture is NRTL Listed for United States and Canada Class 1 Division 1 and Class 1 Division 2 for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist. This unit features a built in emergency battery backup and carries a T6 temperature rating with approval for paint spray booth use.The EPL-EMG-48-216 fixture is a 4 foot long, 4 lamp, Class 1 Division 1 and Class 2 Division 1 & 2 explosion proof fluorescent light which is also approved for use in paint spray booth applications. This T6 temperature rated fixture comes standard with four T5 high output fluorescent lamps. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture is multi-voltage capable and is available with a variety of lamp options. The EPL-EMG-48-216 provides operators in hazardous locations with a reliable and affordable lighting solution that provides the best explosion proof protection available without sacrificing light quality or fixture durability.Click here to view the LED version of this fixture.Click to EnlargeClick to Enlarge Click to Enlarge Click to Enlarge Click to Enlarge Click to Enlarge This fluorescent light works, mounts and is wired like our EPL-48-216 explosion proof fluorescent light fixtures. The main difference is that we attach an extra Bodine ballast box to the unit that adds emergency light functionality to the fixture. This explosion proof emergency light will run the standard 90 minutes after power is lost. The light automatically recharges the battery once electrical power is restored. Standard configuration includes a single emergency ballast that will run two of the four bulbs for 90 minutes at 900 lumens. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fluorescent light.Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit).Made in USA QualityLamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Larger ballast box accommodates High Output lamp ballasts. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.F54-T5/850/HO – 54 watt, 5000 lumens per bulb, 20,000 hours life, 5000 Kelvin color, CRI 85 RHA-UNV-254-LT5 Ballast is THD < 10% and HPF .98 (Suffix –50KT5)F54-T5/841/HO - 50 watt, 4450 lumens per bulb, 20,000 hour life, 4100 Kelvin color, CRI 85 (Suffix -41KT5)Specifications / Additional Information EPL-EMG-48-216 Explosion Proof RatingsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and DLamp Type: Fluorescent Class 1 Division 2, Group A,B,C,DDimensions: W-11.25" L-52" H-8.5 " NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Weight: 70 Lbs NRTL Certified to UL 844, 924Voltage:Universal 120V-277V 50/60 Hz NRTL Certified to UL 1598 Marine TypeTotal Watts: 216 watts Class II Division 1 and 2, Groups E,F,GTotal Lumens: 20,000 Certified Canadian StandardsLuminous Efficacy: 92 Lm/W Listed for Paint Spray Booths*Lamp Life Expectancy: 20,000+ Hours California Title 24 CompliantColor Temp: 5000K (-50KT5) OR 4100K (-41KT5) Switch Leg for Powering Light On/OffAmbient Operating Temp Range: -20 C to 70 C* Operating Temp Rating: T6 Minimum Operating Temp -30¡C Maximum Case Temp: 90¡C Mounting: Surface Standard - Pendant Optional Special Orders- RequirementsContact us for special requirements? Toll Free: 888-325-4448Intl: 1-903-270-1187*Temperatures above 65 degrees C will diminish ballast life from 5 years to 3 years)E-mail: [email protected]