Larson Electronics LED Light Bar - 20 LEDs - 60 Watts - Flood Pattern - Boat LED Lights

Buy American Compliant The Larson Electronics LED-BL-20 LED Boat Light offers high light output from a low profile, light weight, durable and waterproof fixture. This IP67 rated LED light bar is designed with low profile hinge mounts that allow 180 degrees of angle adjustment and produces 3600 lumens of LED light while drawing only 5 amps on 12 volts. This light can run on any voltage from 9 to 42 volts and provides a durable and powerful lighting solution ideal for use in marine environments as well as industrial and commercial applications such as machine vision system lighting, security illumination, exterior building lighting and applications where a low amp draw, waterproof, high intensity light source is required. The LED-BL-20 LED boat light from Larson Electronics produces 3600 lumens of bright light while drawing only 60 watts @5amps from a 12 volt electrical system. Twenty Edison Edixeon¨ Emitters containing CREE EZBright¨ three watt LEDs producing a maximum of 180 lumens each are arranged in rows and paired with 35 degree optics to to produce a wider beam spread and more light over a larger area nearer the fixture. We also offer optional spotlight versions with 10 degree optics to produce a much longer reaching beam with more light concentrated in a tighter pattern. At only 2.75 inches high with a 3 inch depth, this unit has a very low profile that allows mounting in areas where normal incandescent lamps either would not fit or would block other equipment. These LED light bars are IP67 rated and waterproof to 1 meter, sealed against intrusion by dust and dirt and constructed to withstand the demanding conditions found in marine environments. Click here to read an article on the advantages of LED Boat lights over incandescent, fluorescent, or HID Boat lights. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. As a result, many manufacturers reduce the output of their LEDs to reduce the amount of heat produced. These LED light bars utilize an extruded aluminum housing that incorporates an advanced heat radiating fin design which dissipates heat efficiently to produce the maximum amount of power and longevity from the integrated 3 watt LEDs. The end result is more light and longer LED life with higher average lumen maintenance after 50,000 hours. Voltage Control: These units contain an internal voltage regulator which allows them to adjust input current to provide the correct LED voltage levels regardless of input levels from 9 to 42 VDC. These LED light bars can operate on current ranging from 9 to 42 VDC without any modifications necessary as a result. This multi-voltage capability makes these units ideal for mobile and stand alone applications such as those found on boats and vehicles where power systems don’t always operate with 12 volts and external generators, transformers or inverters are impractical. LED-BL-20 35¡ Flood Beam(Stnd) LED-BL-20 10¡ Spot Beam(Opt) Durability: These LED boat lights from Larson Electronics offer IP67 rated construction that is designed to withstand demanding environmental and operating conditions. These LED lights are light weight, compact and designed for versatile mounting options, allowing them to be used in spaces where room is at a premium. They offer extruded aluminum housings, stainless steel hardware and polycarbonate lenses that provide good durability, yet are slimmer and lighter than extreme duty LEDLB-E series lights. These units can operate in temperatures ranging from -40 degrees Celsius to 80 degrees Celsius, are waterproof to 1 meter and are sealed against the ingress of dust, dirt and humidity. The Edison 3 watt LEDs offer inherent LED resistance to shocks and vibrations, contributing to these unit’s 15.6G rating of vibration tolerance. Mounting: Larson Electronics LED light bars are equipped standard with aluminum mounting blocks which slide within the aluminum housing to allow users to adjust their positioning to match existing or user drilled mounting holes. Each aluminum mounting block has an integrated rubber bushing to absorb vibrations and shocks. To secure the lights in place users simply slide the mounting bolts through the aluminum mounting block and rubber isolator, through the mounting surface, then secure the bolt with a locking nut on the opposite side of the mounting surface. This mounting system enables mounting to flat or round surfaces and allows for minimal 7 degrees of flexibility of angle placement of the light. We also offer a BC-2 bar clamp mouting system for LED Boat Lights for even greater mounting versatility. Note: Most Larson Electronics LEDLB, LEDP3W, LEDP10W, and LED10W series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. Looking for more light output? Click here to see the full range of LED Boat Lights offered by Larson Electronics. Specifications / Additional Information LED-BL-20 LED Boa Light Bar LED-BL-20 LED Features LEDs: Edison Edixeon¨ 3 Watt LED Emitters Edison Edixeon¨ 3 Watt LED Emitters Dimensions: 12"-L 2.75"-H 3"-D LEDs Driven At 80% Watts: 60 -40 C~ +80C Operating Temp Range Voltage: 9-42 VDC Spot Beam: 800`L x 80`W Flood Beam: 250`L x 250`W 180 Lumens per LED Weight: 5 Lbs 70% Lumen Retention @50,000 hours Lighting Configuration: 10¡ Spot or 35¡ Flood IP67 Rated Waterproof to 1 meter Mounting: Flat Surface or Tube - Adjustablet Downlaod Spot and Flood Beam Specs Wiring: Deutsch IPD / LADD DT04-2P Amps: 5 (on 12 volts) 2.5 (on 24 volts) Lumens: 3600 Special Orders- Requirements LED Light Color: 6000K or 3000K Contact us for special requirements LED Life Expectancy: 50,000 hours Toll Free: 888-325-4448 Optics Efficiency: 80% Materials: Aluminum Housing, Polycarbonate Lens E-mail: [email protected] Housing Colors: Black or White *Click here to learn about IP ratings and how it applies to your LED Boat Lights. CE Certified 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement. Scroll Down to Purchase-