Larson Electronics Hazardous Location Fluorescent Lighting - 4' 4 Lamp Fixture - T8 - Polycarbonate Lens - C1D2 / C2D2

Made in the USAThe Larson Electronics HALS-48-4L-PC-T8 Hazardous Area Fluorescent Light Fixture is NRTL Listed for United States and Canada listed Class 1 Division 2 Groups A, B, C, D, NRTL Certified to UL 1598, and ideal for use in industrial hazardous locations where wet conditions and chemical/petrochemical vapors may be encountered.***PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO THIS HAZARDOUS LOCATION LIGHT FIXTURE***The HALS-48-4L-PC-T8 fixture is a 4 foot long, 4 lamp, Class 1 Division 2 Groups A, B, C and D hazardous area fluorescent light and a good choice for use in industrial applications and wet areas. This fixture is T4A temperature rated and comes standard with F32/741 T-8 bulbs. The housing on this unit is constructed of powder coated 16 gauge steel for durability and contains a hinged reflector and ballast tray for easy and safe servicing. The lamps are held in place by spring loaded sockets and protected by a hinged polycarbonate door with a polycarbonate (Lexan) lens which is secured with four turn latches.This fixture is multi-voltage capable and can be operated with voltages of 120-277 VAC. This fixture is IP65 rated water and dustproof and approved for wet and marine locations. This fixture also features multiple 1/2 NPT wiring hubs with two located on top of the fixture at two more located at each end, allowing operators to through-wire multiple units in series or mount the unit with wire through conduit pendant mounts.This fixture also features multiple 1/2 NPT wiring hubs with two located on top of the fixture at two more located at each end, allowing operators to through-wire multiple units in series or mount the unit with wire through conduit pendant mounts.Energy Consumption ComparisonT5HO T8 LEDWattage 216 watts 128 watts 112 wattsAmp Draw @ 120V AC 1.80 amps 1.07 amps 0.93 ampsAmp Draw @ 220V AC 0.98 amps 0.59 amps 0.51 ampsAmp Draw @ 240V AC 0.90 amps 0.54 amps 0.47 ampsAmp Draw @ 277V AC 0.78 amps 0.47 amps 0.40 ampsAmp Draw @ 12V DC 18 amps 10.67 amps 9.33 ampsAmp Draw @ 24V DC 9 amps 5.34 amps 4.67 ampsLamp Life Expectancy 20,000 hours 24,000 hours 50,000 hoursOperation cost per year(12hs/day @ 12c/kWh) $113.53 $67.28 $58.86Adjustable Surface Mount Brackets: Two L-brackets enables it to be simply secured to any flat surface. Three through holes provide sufficient mounting for any environment. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be repositioned by removing the adjustment bolts, rotating the fixture, and re-inserting the adjustment bolts in pre-drilled holes.Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture is equipped with two 1/2” NPT hubs, one on each end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to one of the NPT hubs and tied in to the fixture’s lead wires, completing the electrical connection. The remaining pendant hub provides support for the opposite end of the fixture.Suggested Applications: Aircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Chemical manufacturing, Waste treatment plants, Gas processing plants.Made in USA QualityLamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture housing constructed of white powder coated 16 gauge steel.4. Relamping done via 4 turn latches, which enable the operator to unlatch the hinged door and access the lamps.5. Heavy gauge hinged reflector with high gloss reflective finish. Resists dents and corrosion.6. Multiple 1/2 inch, threaded NPT access holes for through wiring. 7. Units can be wired end to end in series.F32-T8/841 – 2800 lumens per bulb, 24,000 hours life, 4100 Kelvin color Specifications / Additional Information HALS-48-4L-PC-T8 Hazardous Location Lighting Ratings/Approvals? ?Dimensions: 12-3/16"-W x 51-1/2"-L x 5-5/16"-H Class I, Division 2, Groups A, B, C, DWeight: 45 Lbs Class II, Division 2 Groups F,GVoltage: Universal 120-277VAC 50/60 Hz Class IIITotal Watts: 128 watts NRTL Certified to UL 844Total Lumens: 11,800 NRTL Certified to UL 1598Lamp Life Expectancy: 24,000+ Hours IP65Luminous Efficiency: 92 Lumens per Watt Wet Area SuitableColor Temp: 4,100K Quick Release Draw Latches & Hinged LensColor Rendering Index: 85 Ease-of-Access Front Access ServiceabilityBeam Angle: 150¡ Adjustable Surface Mount BracketsOperating Temp Range: T3C-T4A Rated Made in the USAHousing Material: Powder Coated 16 Gauge Steel NRTL Listed for United States & CanadaLens Material: Polycarbonate (Lexan) Special Orders- RequirementsMounting: Surface Bracket Standard - Pendant Optional Contact us for special requirementsWiring Hub: 1/2" NPT - (2) On Top, (2) On Ends Toll Free: 888-325-4448Fax: 1-903-498-3364? E-mail: [email protected]