Larson Electronics Explosion Proof Fluorescent Fixture - 2 Foot, 2 Lamp - Class 1, Div. 1 - Low Voltage 9-32 VDC

Made in the USAThe Larson Electronics EPL-24-2L-LV 12V/24V Explosion Proof Fluorescent Light Fixture is NRTL Listed for United States and Canada Class 1 Division 1, Class 1 Division 2, has a T6 temperature rating and is ideal for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to existClick here to see the LED version of thisThe EPL-24-2L-LV fixture is a 2 foot long, 2 lamp, Class 1 Division 1 and Class 2 Division 1 & 2 explosion proof fluorescent light which is also approved for use in paint spray booth applications and a good choice for use in applications requiring a low voltage source of illumination. This T6 temperature rated fixture comes standard with T8 bulbs, and is designed to operate on 12 or 24 volts only. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish.This fixture is multi-voltage capable and provides operators in hazardous locations with a reliable and affordable low voltage lighting solution that provides the best explosion proof protection available without sacrificing light quality or fixture durability. NOTE ON LAMPS: All hazardous location lights are shipped with bulbs. This fixture comes equipped with F17-T8/841 lamps producing 1,200 lumens per bulb, 20,000 hours of service life and a 4100 Kelvin color. Because of the fact that the fixture is low voltage, only T8 bulbs are available. The unit has an electronic ballast and only works with 12 or 24 volt lamps. Please specify your desired voltage option from the drop down menu below when ordering Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fluorescent light. Made in USA Quality Lamp Options 1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Larger ballast box accommodates High Output lamp ballasts. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.8. Spring loaded sockets on both ends hold lamps firmly for maximum shock and vibration protection. F17-T8/841 – 17 watt, 1200 lumens per bulb, 24,000 hours life, 4100 Kelvin color (Suffix –T8) Specifications / Additional Information EPL-24-2L-LV Explosion Proof RatingsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and DDimensions: W-11.25" L-27.5" H-8.5 " Class 1 Division 2, Group A,B,C,DWeight: 30 Lbs NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Total Watts: 34 watts NRTL Certified to UL 844, 924Voltage: 12V - 24V NRTL Certified to UL 1598 Marine TypeTotal Lumens: F17-T8/841 Bulbs 2400 Class II Division 1- 2, Groups E,F,GLamp Life : F17-T8/841 Bulbs 24,000 Hours Certified Canadian StandardsEfficiency: F17-T8/841 Bulbs 184 Lumens per Watt Listed for Paint Spray Booths*California Title 24 CompliantAmbient Operating Temp Range: -30 C to 70 COperating Temp Rating: T6 RatedMinimum Operating Temp: -30 CMaximum Case Temp: 90 C Beam Angle: N/A Special Orders- RequirementsColor Temp: 4100K-STD-F17-T8/841 Bulbs Contact us for special requirementsMounting: Bracket Standard - Pendant Optional Wiring Hub: 1/2 inch threaded Toll Free: 888-325-4448?Intl: 1-903-270-1187E-mail: [email protected]