Larson Electronics Class I, Div II Fluorescent Fixture - Corrosion Resistant (Saltwater) - 2' Fixture - Bi-Axial Design

Made in the USA The Larson Electronics HALP-24-2L-BX Hazardous Area Fluorescent Light Fixture is U.S / Canada U.L approved Class 1 Division 2 Groups A, B, C and D - UL 1598A listed, has a T4A temperature rating and is specifically designed to handle the rigors of wet and corrosive marine environments. This fixture uses Bi-Axial design bulbs to increase wattage and light output without increasing fixture size or weight. The HALP-24-2L-BX hazardous area fluorescent light fixture builds on the effectiveness of our HALP-24 series by including bi-axial lamps which raise the fixture`s wattage and light output totals without increasing the unit`s size or weight. Although some efficiency is sacrificed for increased output, this unit`s lower cost and increased ouput helps offset this lower efficiency. This Class 1 Division 2 rated fixture is constructed of non-corrosive materials including a polyester housing reinforced with glass fiber, a poured in gasket for reliable sealing and an impact resistant acrylic diffuser. Corrosion resistant plastic latches secure the lamp cover to the housing and provide a firm lock against the poured in seal to prevent drips and water intrusion. This fixture is UL 844 rated and Class 1 Division II, Groups A, B, C, D approved. The HALP-24-2L-BX also carries a UL 1598A outdoor marine rating and meets US Coast Guard specifications. This fixture ideal for hazardous areas where corrosion resistance is mandatory and space limitations require a powerful yet compact lighting solution. NOTE ON LAMPS: This fixture comes equipped with Bi-Axial Bulbs which increases the wattage of the standard HALP-24-2L from 48 watts with 2 standard T5-HO lamps to 80 watts with bi-axial bulbs. The HALP-24-2L-BX has an electronic universal voltage ballast and works with 120-277 ACV. Surface Mounting: Flange type aluminum brackets attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide some shock absorbency protection while enabling the user to simply mount the fixture with the through-hole taps that protrude on each side of the fixture. The mounting holes are 14.91" inches on center apart along the top of this hazardous location light. The mounting holes are 9.5" inches on center across the top of the light. Pendant Mounting: This light fixture can hang from the ceiling suspected by rigid pipe. Each fixture is equipped with either two 1/2" or 3/4" NPT hubs on either side of the fixture. Operators will bring rigid pipe down to the threaded mounting hubs. The wiring is fed down through the rigid pipe to one of the NPT hubs and tied to the fixture`s lead wires to complete the electrical connection. The remaining pendant hub provides support for the opposite end of the fixture. Suggested Applications: The HALP-24-2L-BX is designed for marine wet and damp locations, where corrosion resistant fluorescent lights are required. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas, water treatment areas, processing plants and marine loading docks. Made in USA Quality Lamp Options 1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface.3. Fixture housing constructed of glass fiber reinforced polyester.4. Relamping done via stainless steel snap locking latches, which enable the operator to remove the door and access the lamps.5. Lamp cover-diffuser constructed of high impact acrylic for corrosion resistance and lamp protection.6. 1/2" or 3/4", threaded access hole for wiring conduit. N/A Specifications / Additional Information HALP-24-2L-BX Hazardous Area U.L. Ratings UL Listings: United States - Canada Class I Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Dimensions: L-25.88” x W-7.21” x H-5.43” UL 844 Weight: 10.8Lbs UL 1598A Marine Type (Salt water)California Title 24 Compliant Total Watts: 80 watts* cUL Listed for Canada Voltage: 120-277 AC 50/60Hz Meets USCG Specs Total Lumens: N/A T4 Temperature Rating Lamp Life Expectancy: 20,000 Hours Efficiency: N/A Operating Temp Range: T4A Rated -30 C to +70 CMinimum Operating Temp: -20 CMaximum Case Temp: 70 C Beam Angle: N/A Special Orders- Requirements Color Temp: N/A Contact us for special requirements Surface Mounting: Flange type aluminum brackets Toll Free: 1-800-369-6671 Pendant Mounting (2) 1/2" or 3/4" hubs on either side of fixture Wiring Hub: (2) 1/2" or 3/4" threaded on eiether side E-mail:[email protected] U.L Approval: U.S Certificate Canada Certificate Meets US Coast Guard specifications. *Wattage totals are lamps only and may vary with different lamps.