Larson Electronics C1D2 LED Emergency Light - 2 foot 2 lamp - Powers On Only During Power Outages - Pivoting Bracket

Made in the USAThe Larson Electronics HAL-EMG-24-2L-LED-BMSW-113 Hazardous Area LED Emergency Light Fixture is NRTL Listed for United States and Canada Class I Division 2 Groups A, B, C and D - NRTL Certified to UL 1598A listed, has a T4A temperature rating and ideal for hazardous locations where flammable chemical/petrochemical vapors may be occasionally encountered. The HAL-EMG-24-2L-LED-BMSW-113 only powers on during power outages.The HAL-EMG-24-2L-LED-BMSW-113 emergency LED fixture is a 2 foot long, 2 lamp, Class I Division 2 Groups A, B, C and D hazardous area LED light that takes the reliability and efficiency of a fluorescent fixture and adds even longer lamp life and efficiency with high output LEDs. This fixture is T4A temperature rated and comes standard with our high power 14 watt LED lamps. The lamps are protected by a powder coated aluminum frame and shatter and heat resistant clear acrylic lens secured with six zinc coated steel draw latches.The fixture is constructed of copper free aluminum alloy and powder coated. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture can be configured to run on 120 to 277V AC as well as 12-24V DC and is NRTL Certified to U.L. 595 and UL 1598A Marine Type approved for use marine environments and powers on only during power outages or power failures. The HAL-EMG-24-2L-LED-BMSW-113 is weatherproof and provides operators in hazardous locations with a highly efficient, reliable and affordable lighting solution for open areas where flammable chemicals and vapors may occasionally be present.This emergency backup only LED light mounts and is wired like our HAL-EMG-24-2L-LED-BMSW hazardous location LED light fixtures. The main difference is that we add a battery backup unit that adds emergency light functionality to the fixture. With an integrated emergency ballast, this explosion proof LED light will continue to operate both LED lamp for 90 minutes for a combined 3,500 lumens after the main electrical power to the light is severed. Once standard electrical power is restored, the emergency battery pack will be recharged. This light ONLY illuminates under emergency operation when power has been lost to the light fixture.LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life.LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases, vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps.Click Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeWith an integrated emergency ballast, this explosion proof LED light will operate both LED lamps for 90 minutes once the main electrical power to the light is severed. Once standard electrical power is restored, the emergency battery pack will be recharged. This fixture includes a test button in order to check operating accuracy under normal conditions.We have eliminated the ballast normally associated with fluorescent fixtures which reduces overall weight, increases lamp life to an extreme 50,000 hours and helps this LED fixture maintain a T4A temperature rating. The solid state design of the included LED lamps give this fixture superior resistance to damage from vibrations and extremes in temperature as well as a lamp service life over twice that of standard T8 bulbs. The 14 watt LED lamps produce more illumination than standard T8 bulbs, but draw only 3/4 of the current. The current generation of Larson Electronics LED T-series style bulbs produce 15% more light than standard T8 bulbs. This fixture is multi-voltage capable (not multi-tap) and works on the following voltages: 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ, 277 Volts 60 HZ. We also make a 12-24V DC version for low voltage applications (-LV suffix). Our HAL-24-2L-LED LED light fixture is both NRTL Listed for U.S. and Canada.Standard Surface Mount Brackets: Each L bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two bolts on either side of the bracket. The bolts act as a set screw. The bracket itself is mounted via a single bolt hole at the top of the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be pivoted by loosening the cap screws that hold the bracket to the mounting peg. This fixture allows 45 degrees of pivot from the 90 degree point.Suggested Applications: Aircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Chemical manufacturing, Waste treatment plants, Gas processing plants.At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs.Made in USA Quality Superior LED Benefits1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed streamlined ribbed corrosion-resistant, copper free extruded aluminum body for better hear dissipation and extended ballast life. 4. Aluminum extruded lens frame for greater strength5. Relamping done via 10 draw latches, which enable the operator to unlatch the lens and access the lamps.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. 1/2" or 3/4", threaded access hole for wiring conduit. 7. Units can be wired end to end in series.8. Powers on ONLY during power outages.1. 50,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces energy use and prolongs life-spans of peripheral cooling units (A/C, refrigeration)5. 100% recyclable.6. No toxins-lead, mercury.7. No UV light, infrared radiation or CO2 emissions.8. Qualifies buildings for LED and other sustainable business certifications.9. Bright, even light maintains consistent color over time.10. Instant on/off - No flickering, delays or buzzing. 11. Very good color rendering.12. Vibration/impact resistant.13. Significantly cooler operation.14. Less frequent outages, higher output improves workplace safety.Specifications / Additional Information HAL-EMG-24-2L-LED-BMSW-113 HAzardous Area Emergency LED Light RatingsNRTL Listed for United States & Canada Class I Division 2, Groups A, B, C and DLamp Type: Emergency LED NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Dimensions: W-7" L-25 1/2" H-6 1/8" NRTL Certified to UL 1598A Marine TypeWeight: 14 Lbs California Title 24 CompliantVoltage: Multi- 120V-60hz 220V-50hz 240V-60hz 277V-60hz Switch Leg for Powering Light On/OffLow Voltage (Optional): 12-24V DC Emergency Fixture Powers On Only During Power OutagesTotal Watts: 28 watts Both lamps power on in power outagesTotal Lumens: 3,500 Luminous Efficacy: 125 Lm/W LED Lamp Life Expectancy: 50,000 Hours Color Temp: 5300K - Color Rendering Index - 75 Beam Angle: 150¡ Ambient Operating Temp Range: -30¡C to +85¡C Operating Temp Range: T4A rated Minimum Operating Temp: -30¡C Maximum Case Temp: 90¡C Special Orders- RequirementsMounting: Back Mount Swivel Bracket Contact us for special requirementsWiring Hub:1/2" or 3/4" NPT Threaded Hub Toll Free: 1-800-369-6671Intl: 1-903-270-1187? E-mail:[email protected]