Larson Electronics Blue LED Spotlight - 25 Watt 2250 Lumen - 9-60V DC - IP67

The LEDWL-25W-BLUE Blue LED Spotlight is an ultra compact LED light produces a 2,250 lumen output with low amp draw, 50,000 hour service life, and 9 to 60 volt compatibility providing operators with a versatile and powerful lighting. The LEDWL-25W-BLUE Blue LED from Larson Electronics produces 2250 lumen of sharp blue light while drawing 2.09 amps from a 12 volt electrical system. Five 5-watt blue LED producing 450 lumens each are combined with high output parabolic reflector to produce a narrow 5¡ degree spread spot beam, providing a high intensity center beam which is visible during daytime and nighttime operations. This particular unit is ultra compact at only 6" tall by 3.91" wide by 3.36" deep, which makes it ideal for applications where electrical power and mounting space is at a premium. Voltage: The drivers in this unit provide the ability to automatically monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels across a specific range. These LED lights can operate on current ranging from 9 to 60V DC without any modifications necessary as a result. (347-480V AC and 120-277V AC available upon request). This ability to sense and adjust input current also provides protection against voltage spikes and drops that can occur in electrical systems which would otherwise result in burning up or premature LED failure without it. Durability: The LEDWL series LED lights Larson Electronics offer IP67 rated construction that is designed to withstand the rigors of demanding of environmental and operating conditions yet are lighter and smaller than our LEDLB-E series of extreme duty light bars. The this series is designed to provide a low profile, light weight, high performance light bar that can be mounted where other lights will not fit. These units can operate in temperatures of -40¡ Celsius to 80¡ Celsius, are waterproof to 1 meter and resist ingress of dust, dirt and humidity. The housings are formed from extruded aluminum and the lenses are unbreakable polycarbonate. The LEDs offer inherent LED resistance to shocks and vibrations contributing to these units 15.6Grms rating of vibration tolerance. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or “duty cycle” accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each LED based upon the LED’s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 100% capacity without overheating or visible loss of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually on or off. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 50,000 hours. Mounting: The LEDWL-25W-BLUE is suspended within a form fitting trunnion (yolk-type) mount. This trunnion mount has two knurled knobs that can be loosened, allowing the LED light to be adjusted and then re-tightened to lock the light into any desired position once mounted. A single stainless steel stud protrudes from the bottom of the mount, enabling the operator to install the light using a simple through-hole mount, allowing the unit to be installed anywhere a 1/2-inch hole can be drilled. Note: Most Larson Electronics LEDLB, LEDP3W, LEDP10W, LED10W, and LEDP WRE series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB, LEDP10W and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. Specifications / Additional Information LEDWL-25W-BLUE LED Light Internal LED Driver Features Lamp Type: Blue LED Fast average current control Dimensions: 6"-H x 3.91"-W x 3.59"-D Short Protection w/ Skip Mode Watts: 2 lbs Ambient Op Temp -40C to +85C Voltage: Universal 9-60V DC Pin-compatible with the HV9910B Watts: 25W Visible With High Illuminate Warehouse Lighting Lumens: 2,250 Luminous Efficacy: 90 Lm/W CE Certified LED Light Color: Blue EMC Certified LED Life Expectancy: 50,000 hours EMI Certified Led Drive %: 90% View Avg-Mode Driver Control PDF Lighting Configuration: Combo 10¡ Spot & 60¡ Flood Amps: 2.09 @ 12V DC - 1.05 @ 24V DC Ambient Operating Temp Range: -40¡ C to +80¡C Housing Material: Die Cast Aluminum Housing Colors: Black Lens Material: Polycarbonate Special Orders- Requirements Reflector: Parabolic Contact us for special requirements Mounting: Adjustable Trunnion Bracket / Stud Mount Toll Free: 888-325-4448 Wiring: Deutsch IPD / LADD DT04-2P connector Warranty: Yes - 1 Year* E-mail: [email protected] Scroll Down to Purchase-