Larson Electronics 60W Low Profile Underwater LED Light - 10-30V DC - Dual Blue/White - Bronze Finish

The LEDEUL15 Underwater LED light from Larson Electronics produces 6,000 lumens of light while drawing only 60 watts @ 5 amps on a 12 volt electrical system. This powerful and compact underwater LED light is available in white and blue color spectrum, and offers a safer and highly durable 1/2" through-hole surface mounting alternative to other units, which require drilling large mounting holes in the hull and complex sealing. The LEDEUL15 underwater LED light produces 6,000 lumens of bright light is available in white and blue color spectrum output. This unit is constructed of stainless steel and is designed to be surface mounted to the hull while a small 1/2 inch protrusion containing the power wires extend through the hull, allowing the unit to be wired from the other side. This mounting method protects the wires from abrasion and intrusion from water while also greatly reducing the size and/or amount of holes that must be drilled in the hull for installation. This underwater boat light produces a total of 6,000 lumens while drawing only 60 watts at 5 amps from a standard 12 volt electrical system. This unit can be operated with voltages ranging from 10 to 30V DC and is constructed of stainless steel with a bronze finish for durability and resistance to corrosion. The entire unit measures only 3.94 inches in diameter by 0.85 inches thick, making it very low profile and easy to mount unobtrusively on the hull below the waterline. This LEDEUL15 has three operating modes: cross fade, solid, and strobe. The white/blue combination has four modes, with a solid white and solid blue. Please note, the cross fade and strobe functions are designed to randomize color patterns. These lights are not designed to be synchronized. LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life. LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases, vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps. Mounting: Mounting is accomplished with three, through holes and screws for securing the light to the hull. A 1/2 inch base extension in the center of the light containing the wiring connections passes through the hull for secure through surface wiring. In boating applications the operator can drill a 1/2 inch hole in the hull and insert the base mount, passing the base extension through the hull. The 2 wire installation can then be done inside the hull. The wires or points of ingress around the wire are thus not exposed to the water and protected against chafing or damage from rubbing against the edges of the mounting hole. We also carry an alternative underwater LED unit that is submersible to 60 meters you can view here. Applications: Boat lights, underwater boat lights, cabin lights, interior/exterior lighting, marine locations, vessels, docks, control rooms, general area illumination and more. At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs. Specifications / Additional Information LEDEUL15 Underwater LED Light Ratings/Features Lamp Type: LED Bronze Alloy Finish Dimensions: 3.94"-Diameter 0.85"-Depth Waterproof to 6 feet Watts: 60 Timed Toggled Protocol Voltage: 10-30V DC Lumens: 6,000 LED Life Expectancy: 50,000+ Hours LED Color: White/Blue Color Temperature: 6500K Color Rendering Index (CRI): 70+ Special Orders- Requirements Amps: 5A @ 12V DC, 2.5A @ 24V DC Contact us for special requirements Ambient Operating Temperature: -31¡C to +55¡C Phone: 1-214-616-6180 Materials: Stainless Steel w/ Bronze Finish Toll Free: 888-325-4448 Mounting: Surface/Wall via 1/2" Mounting Holes Fax: 1-903-498-3364 Wiring: 3-wire Leads E-mail: [email protected] Scroll Down to Purchase-