Larson Electronics 36 Watt LED IR Light Emitter - 12 IR Emitters LED's - 9-42VDC - Extreme Environment

Buy American Compliant The LEDP10W-120X2E-IR LED Infrared Light Bar offers high infrared light output in a light weight, durable, low profile housing combined with versatile mounting and power options. This IP67 rated infrared LED light bar is waterproof to one meter and produces 3,600mW of infrared light while drawing only 36 watts of power at 3 amps from a 12 volt electrical system. This light can run on any voltage from 9 to 42 Volts DC and produces an infrared light beam that can only be seen through the use of night vision goggles. We also offer other wavelength options they include 750Nm, 850Nm or 940Nm. TheLEDP10W-120X2E-IR LED infrared light bar from Larson Electronics produces a 550` long by 70` wide infrared light beam with 3,600mW of light in the infrared spectrum while drawing only 36 watts @3 amps from a 12 volt electrical system. Twelve Edixeon¨ thee watt Infrared Emitters LED`s producing 300mW each are paired with high purity 10¡ degree optics to produce a tightly focused spot beam with limited spread or light spillage. An integral Pulse Width Modulation controller, small profile, low power requirements, high durability and versatile mounting system makes these infrared light emitters a superior lighting solution for a wide array of applications including but not limited to: military, industrial manufacturing, machine visioning, security and law enforcement, boating, vehicles and commercial structure illumination. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or “duty cycle” accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each LED based upon the LED’s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 100% capacity without overheating or visible loss of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually on or off. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 50,000 hours. PWM Control: The pulse width modulation drivers in this unit also provide secondary benefits through the ability to tap into a provided input wire with an external pulse generator and adjust the duty cycle of the current being applied to the LEDs. Thus you can connect an external dimmer, switch or pulse control and adjust the perceived output of the light, effectively causing the light to flash, dim or brighten to the desired levels. Additionally, this method of controlling light output results in a corresponding drop in amperage draw, so if the duty cycle is cut back to 50% there will be a matching 50% reduction in amperage draw. These units are also able to monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels across a specific range. These LEDP10W series light bars can operate on current ranging from 9 to 42VDC without any modifications necessary as a result. This ability to sense and adjust input current also provides protection against voltage spikes and drops that can occur in vehicle electrical systems which would otherwise result in burning up or premature LED failure without it. Durability: As well as unparalleled heat control, this infrared light bar also offers IP68 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40 degrees Celsius to 85 degrees Celsius, are waterproof to three meters and resist ingress of dust, dirt and humidity. The housings are formed from extruded aluminum and the lenses are unbreakable polycarbonate. The Edixeon¨ LEDs offer inherent LED resistance to shocks and vibrations, contributing to these units 15.6Grms rating of vibration tolerance. Mounting: Each unit is equipped with aluminum mounting blocks which slide within the aluminum housing to allow users to adjust their positioning to match existing or user drilled mounting holes. Each aluminum mounting block has an integrated rubber bushing to absorb vibrations and shocks. To secure the lights in place users simply slide the mounting bolts through the aluminum mounting block and rubber isolator, through the mounting surface, then secure the bolt with a locking nut on the opposite side of the mounting surface. This mounting system enables mounting to flat or round surfaces and allows for minimal 7 degrees of flexibility of angle placement of the light. For increased adjustability please see our trunnion mounted versions which add a wider degree of vertical angle adjustment. Note: Most Larson Electronics LEDLB, LEDP3W, LEDP10W, and LED10W series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB, LEDP10W and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. LEDP10W-120X2E-IR 40¡ Flood Beam(Opt) LEDP10W-120X2E-IR 20¡ Wide Spot Beam(Stnd) CONDITIONS Vin min (V) = 9 toff (us) = 2.9 Vin nom (V) = 12 R1 (kohm) = 50.2 Vin max (V) = 50 L1 (uH) = 3.0 Vo min (V) = 6.5 L-Pk (A) = 2.9 Vo nom (V) = 6.8 L-rms (A) = 2.9 Vo max (V) = 7 Ipk (A) = 2.5 I-LED (A) = 2.2 R2 (ohm) = 0.10 Efficiency = .85 I-FET (A) = 2.2 fsw nom (kHz) = 150 fs min (kHz) = 77 Ts nom (us) = 6.666667 fs max (kHz) = 301 Base frequency- = 36~37Khz @ 12V Amplitude of pulse width- = 27Ms Outside: External dimmer- = 500Hz Inside : Current sensing from- 77KHz at 12V to 300KHz at 50V Specifications / Additional Information LEDP10W-120X2E-IR LED Light Bar Internal LED Driver Features Lamp Type: Edixeon¨ LEDs Edixeon¨ 3 Watt LED Emitters Dimensions: 11.9"-L 4"-H 3.5"-D Weight: 7.5Lbs -40 C~ +80C Operating Temp Range Watts: 36 IP67 Rated Waterproof to 3 meter Led Drive %: 90% PWM dimming input Voltage: 9-42 VDC Spot Beam: 550`L x 70`W Flood Beam: 120`L x 100`W Short protection w/Skip mode Lighting Configuration: 10¡ Spot or 35¡ Flood Pin-compatible with the HV9910B Mounting: Flat Surface or Tube - Adjustable Wiring: Deutsch IPD / LADD DT04-2P connector View Avg-Mode Driver Control PDF Amps: 3 (on 12 volts) 1.5 (on 24 volts) Megawatts: 3,600 Wavelength: 750Nm, 850Nm or 940Nm Infrared LED Life Expectancy: 50,000 hours Optics Efficiency: 90% Special Orders- Requirements Materials: Aluminum Housing, Polycarbonate Lens Contact us for special requirements Housing Colors: Black or White Toll Free: 888-325-4448 Flood Beam: Lux @1 meter= 24,000 @3 meters= 3,850 Spot Beam: Lux @1 meter= 31,500 @3 meters= 6,550 E-mail: [email protected] Down to Purchase-