Made in Texas The WCDE-20KW-8X250LTL-LED-220V-MLK-CPR mobile hydraulic light tower from Larson Electronics is a towable lighting package powered by a 20 kW generator. With eight, 240-watt lamps producing 259,200 lumens, this unit will illuminate a 8-9 acre area continuously without refueling for 19+ hours. A Deepsea controller is available for monitoring the real-time status of the IP65-rated unit. The WCDE-20KW-8X250LTL-LED-220V-MLK-CPR mobile hydraulic light tower is a powerful lighting solution for outdoor, remote locations. This unit is supported by a 4-cycle, water cooled, direct injection, natural intake Perkins/404D-22G engine (diesel), which supplies the current to eight, 240-watt LED lamps producing 32,400 lumens each for a combined total of 259,200 lumens of light. The light mast can provide 19+ hours of continuous illumination, at extended heights up to 25 feet. This mobile floodlight package is ideal for emergency services, large scale event illumination, construction, mining, industrial operations and anywhere an extended operation capable mobile lighting solution is needed. With engine speeds of 1,800 rpm, the four-cylinder unit is capable of generating 22 kW on standby and 20 kW during prime use. As a low-rpm generator, it operates quieter than 3,600 rpm "throw-away" models. Because 3,600 rpm generators have higher speeds, the units wear out faster and require less copper during operation. The WCDE-20KW-8X250LTL-LED-220V-MLK-CPR is designed to support 220V 60Hz. It features five power outputs and an ATS plug. This unit will automatically shut down in the event of an abnormal condition related to water temperature, engine oil pressure, low coolant, low DEF, overspeed and overcrank. An emergency stop switch allows operators to manually shut down the system. Lights: The lighting system on this unit is comprised of eight, 240-watt LED lamps producing 32,400 lumens of light each attached to the end of the telescoping light boom. These floodlights produce a wide flood light pattern capable of illuminating an area of 8-9 acres with a combined total of 259,200 lumens of light. Each floodlight is securely fastened to the light boom and each lamp includes a support bracket to help maintain lamp stability within its housing. The lamps are connected to the power source via a water tight male pin connector that attaches to a receptacle located on the end of the telescoping boom. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units feature individual heat sinks per bank of six LEDs to control heat buildup rather than utilizing a single housing to dissipate heat. This allows for more thorough cooling of the LEDs for extended operating periods. This allows the LEDs to be driven at up to 90% capacity without overheating or visible loss of light output. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 80,000 hours. In addition, should an LED failure occur, these LED flood lights are field serviceable. Each bank of six LEDs can be replaced with the fixture installed. This allows for the tower to stay in operation until repairs can take place, and eliminates the need to remove and disassemble the entire fixture for repairs. Durability: As well as unparalleled heat control, the GAU-LTL series of LED lights from Larson Electronics also offer IP67 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40¡ Celsius to +80¡ Celsius, are waterproof, and resist ingress of dust, dirt and humidity. The housings are formed from die cast aluminum and the optics are high transmission PMMA with 98% light transmittance. The Cree¨ LEDs help these units achieve resistance to vibrations and are rated at 70% lumen maintenance after 80,000 hours of use. We use these LED lights for applications where a lot of vibration, dust, dirt, dampness and abusive working conditions are encountered. Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting. Controls: A DSE3110 Deepsea controller provides operators with a wide viewing panel and robust monitoring of the brushless generator. The system displays frequency, battery voltage, runtime and more. A protective feature notifies operators about low oil pressure, high water temperature, over/under voltage and over/under speed. The controller can be used in manual or auto start mode. Configurable timers and alarms provide flexibility and real-time monitoring of the system. Telescoping Boom: The telescoping hydraulic tower on this unit reaches 25.5` when fully extended. Hydraulic operation allows operators to easily raise, lower, or rotate the mast through a full 359¡ of movement as needed. A stepping pad allows operators to make adjustments from the ground with ease. The light heads are trunnion mounted to the mast crosspieces using U brackets and can be individually adjusted while the tower is in the retracted position. The telescoping boom is constructed of aluminum to resist rusting and corrosion and is capable of withstanding 50 mph winds when extended to its full height and the stabilizing outriggers are deployed. The stabilizing outriggers are a four-point design with one located under the trailer tongue, two on the sides and one on the back of the unit. The two side outriggers are adjustable and include 2,000 lbs swivel jacks for leveling and stabilizing the tower. Housing: All of the operating components are housed within a protective compartment constructed of 14 gauge steel and designed to provide airflow for cooling. Side wing doors provide access to the interior while latches provide secure closing when the unit is in use. The design and construction of this enclosure helps this unit operate at a low 65 Db noise level @ 23 ft. The entire unit can be loaded and unloaded onto trucks via forklift sleeves mounted to the top section of the light mast. The entire unit is mounted onto a two-wheel trailer with a 2,200 lbs leaf spring axle. A standard two inch ball coupling and two standard safety chains allow for easy hookup and towing. Applications: This portable generator is suitable for use in remote locations, such as temporary camps, construction sites, military bases and areas without reliable access to the grid. It can be utilized to power a wide range of heavy duty tools and equipment, including laptops, portable machines and mobile devices. The units robust recharging options offer flexibility in environments where access to reliable power sources are severely limited. At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs. Specifications / Additional Information WCDE-20KW-8X250LTL-LED-220V-MLK-CPR Mobile Hydraulic Light Tower Protection Genset Specs: 20kW Perkins Genset Engine: Perkins/404D-22G EPA Tier 4 25 Gallon Fuel Capacity Engine Type: 4-cycle, Water Cooled, Direct Injection, Natural Intake 19+ Hours of Continuous Illumination Engine Speed: 1800 RPM External Grounding No. of Cylinders: 4 Low Oil, High Engine Temp Auto Shut-Off Rated Power: 20 kW Deepsea Controller Rated Standby Output: 22 kW Four Point Outrigger System Generator: Stamford PI144D Steel Trailer w/ Industrial Grade Paint Finish Voltage: 220V 60Hz 3PH High Output LED Lamps Battery 12V @ 60Ah 259,200 Total Lumen Output Fuel Cell Capacity: 25 Gallons Independently Adjustable Light Heads Fuel Delivery: Electric Individual Light Switch Circuit Breakers Noise Level: Db level 65 @ 23 ft Dial-in Adjustability per light head 130 Lumens Per Watt Efficiency Light Mast Specs: Withstands 50Mph Winds at Full Extension Mast Type: Hydraulic 98% Transmission High Purity PMMA Optics Boom Height: Up to 25` 70% Lumen Retention after 80,000 Hours Materials: Aluminum Multiple LED Banks for Heat Dispersion Operation: Hydraulic Stages: Four Features: Coiled Mast Cord, (1) Lifting Eye and Fork Pockets Light Specs: Lamp Type: Cree¨ LED Total Watts: 1,920 (240W per lamp) Total Lumens: 259,200 (32,400 per lamp) Luminous Efficiency: 135 lm/w LED Color Temperature: 4000K or 5000K LED Life Expectancy: 80,000 hours Optics Efficiency: 98% - PMMA High Transmittance Optics LED Drive %: 90% Power Factor: >97% Mounting: Stainless Steel Trunnion Mount U-Bracket Materials: Die Cast Aluminum Housing, Acrylic Optics Housing Color: Natural Aluminum Ambient Temperature Range: -40¡C to +80¡C Waterproof Rating: IP67 Coverage: 8 to 9 Acres Trailer Specs Materials: 14ga Sheet Steel Enclosure, 12ga Formed Steel Chassis Hitch: 2" ball hitch Finish: Industrial Grade Paint Axle: (1) 2,200 lbs Suspension: 2,000 lbs Double Eye Leaf Springs Outriggers: (4) Adjustable Outriggers w/ 2,000 lbs Manual Leveling Jacks Lighting: DOT Approved tail, side, brake, and directional lights Special Orders- Requirements Wheels: (2) 13" 5x4.5 Steel Rims Contact us for special requirements Tires: 155R13 Toll Free: 1-800-369-6671 Dimensions: 137" x 93.3" x 53.9" Intl: 1-903-270-1187 Weight: - E-mail:[email protected] Down to Purchase
Larson Electronics 20kW Generator - Water Cooled Diesel Engine - 25' Hydraulic Tower - (8) LED Lamps - 25 Gal Tank
Larson Electronics
(No reviews yet)
Write a Review
Write a Review
Larson Electronics
Larson Electronics 20kW Generator - Water Cooled Diesel Engine - 25' Hydraulic Tower - (8) LED Lamps - 25 Gal Tank
- SKU:
- WCDE-20KW-8X250LTL-LED-220V-MLK-CPR
- UPC:
- Weight:
- 0.00 LBS
!