Larson Electronics 15 KVA Temporary Power Distribution - 220V to 415V 3P - (1) 220V (4) 415V Receptacles - SS MLO Panel

Made in Texas The Larson Electronics MGL-220V.3P-15KVA-415V.3P-SS-4X32A temporary power distribution system converts three phase 220V AC electrical current into three phase 415V AC. This unit provides operators the ability to safely tap into and distribute 220V AC power from a variety of sources including generators and direct grid power. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO POWER DISTRIBUTION PANELS, TRANSFORMERS, OR SUBSTATIONS* The MGL-220V.3P-15KVA-415V.3P-SS-4X32A temporary power distribution system gives operators the ability to power three phase 220 volt and 415 volt equipment from a single system. On the primary side, operators connect 220 volt line-in power via a customer provided cord. On the secondary side, operators connect to four IEC 60309 415V receptacles for 415V equipment. Operation: A customer provided line-in cord brings 220V three phase power to a 125-amp disconnect on the primary side, which contains three 250V 125-amp time delay fuses protecting the transformer, and passes 220V three phase through to the transformer. The NEMA 3R 15 KVA transformer converts 220V three phase power to 415V three phase and passes the current to the secondary panel. The secondary side of the transformer feeds a NEMA 4 stainless steel, 125-amp 480V three phase main lug only panel. This secondary main lug only panel contains four 30-amp 415V breakers, protecting four 32-amp IEC 60309 415V waterproof receptacles. All receptacles are equipped with weatherproof covers. Protective Construction: The transformer and load center/distribution assembly is mounted to a powder coated steel, dolly cart style, frame resulting in an extremely stable, durable, and mobile power distribution platform. Two run-flat rubber tires and a dolly cart style mounting platform provides easier substation mobility, and a center point lift point allows easy lifting with cable or chain hooks. This temporary power distribution solution can be modified to meet the needs of job-site receptacle requirements. Units are available up to 150 KVA, and can be equipped with skids or trailer mounted. Certification: Larson Electronics is a UL 1640 panel shop and certified to build portable power distribution systems. All units are built in accordance to NFPA 70 (National Electric Code) and certified to UL 1640. All equipment is NEMA 3R rated for indoor and outdoor use and provide a degree of protection against dirt, water, and ice. NEMA 4 and NEMA 4X equipment can be equipped upon request. Grounding: Transformer is grounded to the frame and we provide a grounding lug on the frame for the earth ground. ~Please check all motor loads for dual rated motors that will work 208 or 240.~ Applications: This power distribution system is ideal for indoor or outdoor use and applications including but not limited to, construction sites, plant maintenance, plant turnarounds, shows, exhibits, and shipyard operations. These power distribution systems are popularly used in applications where external power sources are often necessary. We also offer class rated transformers for use within explosion proof and hazardous location environments. Larson Electronics is a manufacturer and as such can build portable transformer systems to your specifications. Although we carry several models of power distribution transformers, we can deliver custom ordered units almost as quickly as our prebuilt units. If this model does not meet your needs, please contact us at 888-325-4448 [email protected] to discuss your specific requirements. Specifications / Additional Information MGL-220V.3P-15KVA-415V.3P-SS-4X32A -Temporary Power Distribution System Ratings/Approvals Line In: Customer Provided UL 1640 Portable Power-Distribution Equipment Primary Voltage: 187-260V AC 3PH NEMA 3R Indoor or Outdoor Use Primary Disconnect: 125A Disconnect 3PH used @ 125A Made in the USA Primary Protection: Disconnect Stainless Steel MLO Panel Transformer: 15KVA 220V to 415V 3PH N3R IP67 Rated Receptacles Secondary Voltage: 415V AC 3PH Secondary Panel: 480V 125A Main Lug Only Panel N4 SS Secondary Breakers: (4) 30A [415V] Secondary Receptacles: (4) 32A, IEC 60309 [415V] Secondary Receptacle Configuration: 4P5W 6H Red Secondary Protection: Weatherproof Covers Form Factor: Powder Coated Steel Dolly Cart w/ Run Flat Tires Dimensions: W-40" X D-40" X H-48" Special Orders- Requirements Weight: 350 lbs Contact us for special requirements Features: Toll Free: 888-325-4448 Max Primary OCP: 125 Amps @ 220V Max Secondary OCP: 125 amps @ 415V E-mail: [email protected] Larson Electronics manufacture a wide variety of custom power distribution systems. The pictures displayed for this unit are a general representation of form factor and may not accurately represent this exact configuration in every detail due to being custom builds. The specifics for this configuration are listed in the specification table and one-line diagram. *All grounding shall comply with state and local codes and meet the minimum requirements of the National Electronic Code section 250* Scroll Down to Purchase