Larson Electronics 12/24V Class 1 Division 2 Light for Hazardous Location Areas

Made in the USAThe Larson Electronics HAL-48-2L-LV Hazardous Area Fluorescent Light Fixture is NRTL Listed for United States and Canada Class 1 Division 2 Groups A, B, C and D - NRTL Certified to 1598A listed, has a T4C temperature rating and ideal for open air hazardous locations where flammable chemical/petrochemical vapors may be occassionally encountered. This low voltage version of the HAL-48-2L is designed to run on 12/24 volts DC. The HAL-48-2L-LV fixture is a 4 foot long, 2 lamp, Class 1 Division 2 Groups A, B, C and D hazardous area fluorescent light and a good choice for use in applications requiring a low voltage source of illumination. This fixture is T4A temperature rated and comes standard with F32-T8 bulbs. The lamps are protected by an aluminum framed hinged glass door secured with four turn latches and the fixture is constructed of copper free aluminum alloy. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish.This fixture is designed to operate on 12 or 24 volts DC only and is NRTL Certified to U.L. 595 and UL 1598A Marine Type approved for use marine environments. The HAL-48-2L-LV provides operators in hazardous locations with a reliable and affordable low voltage lighting solution for open areas where flammable chemicals and vapors my occasionally be present.Click Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeNOTE ON LAMPS: This fixture comes equipped with F32-T8/841 32 Watt lamps producing 2950 lumens per bulb, 24,000 hours of service life and a 4100 Kelvin color. The HAL-48-2L-LV has an electronic ballast and only works with 12 or 24 volt DC lamps. Please specify your desired voltage option from the drop down menu below when ordering..Standard Surface Mount Brackets:Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. Mounting brackets are removable. A single through hole enables the operator to install the light to any surface. A sliding bracket mount kit is also available in the optional accessories menu below for retrofitting this fixture into existing mounting locations.Suggested Applications: Aircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Chemical manufacturing, Waste treatment plants, Gas processing plants.Made in USA Quality Lamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Relamping done via 4 turn latches, which enable the operator to unlatch the hinged door and access the lamps.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. 1/2" or 3/4", threaded access hole for wiring conduit. 7. Units can be wired end to end in series.N/AClick here to see the LED version of this fixture Specifications / Additional Information HAL-48-2L-LV Hazardous Area RatingsNRTL Listed for United States & Canada Class 1 Division 2, Groups A, B, C, DDimensions: W-7" L-49 3/4 " H-6 1/8 " NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Weight: 33 Lbs NRTL Certified to UL 1598A Marine TypeTotal Watts: 64 watts* California Title 24 CompliantVoltage: 12-24 Volts DC Total Lumens: STD-F32-T8/841 Bulbs 5,900 Lamp Life Expectancy: STD-F32-T8/841 Bulbs 20,000 Hours Efficiency: STD-F32-T8/841 Bulbs 92 Lumens per Watt Operating Temp Range: T4A Rated -30 C to 70 C Beam Angle: N/A Special Orders- RequirementsColor Temp: 4100K- Contact us for special requirementsMounting: Bracket Standard - Pendant Optional Toll Free: 888-325-4448Wiring Hub: 1/2" or 3/4" threaded Intl: 1-903-270-1187Minimum Operating Temp: -30 C E-mail: [email protected] Case Temp: 90 C ? Hal-48-2L Dimensional Drawing *Wattage totals are lamps only and may vary with different lamps