Larson Electronics Fluorescent T8 Light w/ Dimmable Ballast - Class 1 Division II - Hazardous Location Areas

Made in the USAThe Larson Electronics HAL-48-2L-T8-D Hazardous Area Fluorescent Light Fixture with Dimmable Ballast is NRTL Listed for United States and Canada Class 1 Division 2 Groups A, B, C and D - NRTL Certified to UL 1598A listed, has a T4A temperature rating and ideal for hazardous locations where flammable chemical/petrochemical vapors may be occasionally encountered.The HAL-48-2L-T8-D fixture is a 4 foot long, 2 lamp, Class 1 Division 2 Groups A, B, C and D hazardous area fluorescent light with dimmable ballast and a good choice for use in applications where space is at a premium. This fixture is T4A temperature rated and comes standard with T8/841 bulbs.The lamps are protected by an aluminum framed shatter and heat resistant clear acrylic lens secured with ten draw latches and the fixture is constructed of copper free aluminum alloy. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture is multi-voltage capable and is NRTL Certified to U.L. 595 and UL 1598A Marine Type approved for use marine environments. The HAL-48-2L-T8-D provides operators in hazardous locations with a compact, reliable and affordable lighting solution for open areas where flammable chemicals and vapors may occasionally be present.Click Photo to EnlargeClick Photo to EnlargeSurface MountPendant MountNOTE ON LAMPS: This fixture comes equipped with F32-T8/841 - 54 Watt lamps producing 2950 lumens per bulb, 24,000+ hours life, 4100 Kelvin color tubes. The HAL-48-2L-T8-D has an electronic multi-voltage dimmable ballast and works with 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ and 277 Volts 60 HZ.Standard Surface Mount Brackets:Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. Mounting brackets are removable. A single through hole enables the operator to install the light to any surface. Pendant mounts are available for operators who wish to mount these fixtures away from the ceiling surface.Suggested Applications:Aircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Chemical manufacturing, Waste treatment plants, Gas processing plants.Made in USA Quality Lamp Info1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed streamlined ribbed corrosion-resistant, copper free extruded aluminum body for better hear dissipation and extended ballast life.4. Aluminum extruded lens frame for greater strength5. Relamping done via 10 draw latches, which enable the operator to unlatch the lens and access the lamps.6. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion. 7. 1/2" or 3/4", threaded access hole for wiring conduit. 8. Units can be wired end to end in series.F32-T8/841 - 32 Watt, 2950 lumens per bulb, 24,000 hours life, 4100 Kelvin colorClick here to see the LED version of this light fixture Specifications / Additional Information HAL-48-2L-T8-D Dimmable Hazardous Area Fluorescent Fixture RatingsNRTL Listed for United States & Canada Class 1 Division 2, Groups A, B, C, DDimensions: W-7" L-49 3/4" H-6 1/8 " NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Weight: 33 lbs. NRTL Certified to UL 1598A Marine TypeTotal Watts:64 watts* California Title 24 CompliantVoltage: Multi- 120V-60hz 220V-50hz 240V-60hz 277V-60hz Total Lumens: F32-T8/841 5,900 Lamp Life Expectancy: F32-T8/841 130,000 Hours Efficiency: F32-T8/84192.18 Lumens per Watt Operating Temp Range: T4A Rated -30¡C to +70¡C Beam Angle: N/A Special Orders- RequirementsColor Temp: 4100K Contact us for special requirementsMounting: Bracket Standard - Pendant Optional Toll Free: 888-325-4448Wiring Hub: 1/2" or 3/4" threaded Fax: 1-903-498-3364Minimum Operating Temp: -30¡ C E-mail: [email protected] Case Temp: +90¡ C ? *Temperatures above +65¡C will diminish ballast life from 5 years to 3 years