Larson Electronics High Intensity LED Light - 20 Watt LED - 12-32V DC - Polycase Inline Switch - No Bar Clamp

Buy American Compliant The BCML-LEDP2X10WRE-ILS Bar Clamp Mount Spotlight with Inline Switch offers high light output in a durable, low profile housing. This light produces a very tight spot pattern, can run on any voltage from 12 to 32 volts and provides a rugged lighting solution ideal for use in marine environments, industrial and commercial applications, heavy equipment illumination, vehicle lighting and law enforcement. The BCML-LEDP2X10WRE-ILS LED bar clamp mount spotlight from Larson Electronics produces a 700` long beam while drawing less than 2 amps on a 12 volt electrical system. Two 10 watt LEDs are combined with high purity optics to produce a tight 10 degree spread spot beam. This fixture is ideal for anyone who is looking for a tight spot light that offers outstanding life hours of 50,000+. These LED bar clamp mount spotlights are IP68 rated and waterproof to three meters, sealed against intrusion by dust and dirt and ruggedly constructed to withstand demanding environments and applications. The housing of this hunting spotlight is constructed of extruded aluminum and features rubber isolated mounts and unbreakable polycarbonate lenses to provide durability and resistance to vibrations, impacts, abuse, hard rains, sand and high winds. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. As a result, many manufacturers reduce the output of their LEDs to reduce the amount of heat produced. These LED light bars utilize an extruded aluminum housing that incorporates an advanced heat radiating fin design which dissipates heat efficiently to produce the maximum amount of power and longevity. The end result is more light and longer LED life with higher average lumen maintenance after 50,000 hours. Voltage Control: These units are able to monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels across a specific range. This BCML-LEDP2X10WRE-ILS can operate on current ranging from 12 to 32 Volts DC without any modifications necessary as a result. This high output LED spotlight draws 1.6 amps @ 12V DC and 0.8 amps @ 24V DC. The multi-voltage capability makes these units ideal for mobile and standalone applications such as those found on commercial boats, heavy equipment and vehicles where power systems don’t always operate with 12 volts and external generators, transformers or inverters are impractical. Durability: The BCML-LEDP2X10WRE-ILS offers IP68 rated construction that is designed to withstand tough environmental and operating conditions. These units can operate in temperatures ranging from -40 degrees Celsius to 85 degrees Celsius, are waterproof to three meters and resist ingress of dust, dirt and humidity. The housings are formed from die-cast aluminum and the lenses are unbreakable polycarbonate. Mounting: The BCML-LEDP2X10WRE is mounted on the end of a 4" shaft chrome plated. An aluminum bar clamp is mounted to the shaft to simplify mounting. These bar clamps are not adjustable. The top portion of the mount has a through hole that enables the operator to pass one of two 1/4 - 20 bolts through it and secure that stud with a Nylock nut. The Nylock nut and bolt are provided with the bar clamp. Small machine screws secure the bottom half of the clamp to the top portion. The installer simply affixes the light to the top portion and places the assembly on the rail or bar. The bottom portion is positioned and secure with the machine screws, cinching the clamp tightly to the bar. Operation: Operator controls rotation and elevation of spotlight outside of vehicle by twisting and turning a handle. The beam remains where the operator places it until the handle is moved. Wiring: Each BCML spotlight comes with a detachable 16 foot coil cord with cigarette plug. The cord is detached via a weatherproof, 2 pin Deutsch connector which easily and securely attaches and detaches the coil cord from the spotlight. An inline on/off switch housed within a waterproof Polycase housing allows operators to easily power the light on or off. Other cords, including 21 foot cords with ring terminals (C-21RT), 16 foot cord with spring battery clamps (alligator clips) (C-16BC) and a 16 foot straight cord with cigarette plug (C-16CP) are available. The veritile mounting and high output adjustable light head make this spotlight ideal for hunting and offroad applications. Being both waterproof and resistant to impacts, vibration, and dusts this LED spotlight is well suited for ATVs, UTVs, 4-wheelers, golf carts, and any other application with a post to mount the light to. Specifications / Additional Information BCML-LEDP2X10WRE-ILS LED Spotlight BCML-LED Features Lamp Type: Two LEDs IP68 Rated Waterproof to 3 meters Dimensions: Light Head - 4.07"-H 3.8"-D; 11 3/8-Total Length LEDs Driven At 90% Watts: 20 -40 C~ +85C Operating Temp Range Voltage: 12-32 V DC PWM Integrated Dimming Circuitry Spot Beam: 700` L Inline Switch Lighting Configuration: 10¡ Spot, 20¡ Wide Spot or 60¡ Flood Mounting: Bar Clamp Wiring: 16` Detachable Coil Cord w/ Cigarette Plug & Inline Polycase Switch Amps: 1.6 @ 12V - 0.8 @ 24V Vibration Rating: 15.6G Special Orders- Requirements LED Light Color: 6000K Contact us for special requirements LED Life Expectancy: 50,000 hours Toll Free: 888-325-4448 Optics Efficiency: 90% Materials: Die Cast Aluminum Housing, Polycarbonate Lens E-mail: [email protected] Housing Color: Black 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, we will ship a new replacement. Scroll Down to Purchase-