Larson Electronics Explosion Proof LED String Lights - 5 lights - Daisy Chain End-2-End Connection - 50ft Stringer

Made in the USA The Larson Electronics EPL-SL-5-LED-E2E Explosion Proof String Light set is UL Listed Class 1 Division 1 Groups C and D and is ideal for general close work and inspection activities in hazardous locations requiring explosion proof protection. This explosion proof string light set from Larson Electronics contains a total of five 10 watt work lights equipped with aluminum hooks and connected in series along 40 feet of 14/3 SOOW explosion proof cord. A molded T junction is mounted every ten feet, with 3 feet of 16/3 SOOW cord connecting a single drop light to the backbone. The cord on this unit is terminated with a 20 amp 5-20 or 6-20 Class 1, Division 1 explosion proof plug for complete protection. With this arrangement, each drop light cannot spark if pulled apart or dragged. A 10 foot tail section of main SOOW cord is included to allow ample length for connection to power sources. An explosion proof outlet at the end of the backbone provides the ability to conenct multiple units end to end, allowing operators to daisy chain multiple stringers together along the jobsite. 10 Watt LED Bulb Molded T Connector w/ Hook Ring 10` whip w/ EXP Plug Click Photos to Enlarge Click Photos to Enlarge Click Photos to Enlarge 100 Watt Incandescent Bulb With the EPL-SL-5-LED-E2E Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting. This unit incorporates five explosion proof LED hand lamps connected in series and is suitable for use in areas where petrochemical vapors and various dusts are present. The machined aluminum housings, cast aluminum guard, tempered glass lamp globe, and abrasion resistant cord make this a very durable unit that will resist damage from chemicals, abrasion, vibrations and impacts. This string lighting solution will provide the lighting you require in a flexible, easy to manage configuration. The hand lamps can be moved around and hooked to different points on your scaffold. The lights, however must remain within 10 feet of one other. Each molded T section contains a hook eyelet, allowing operators to suspend the entire backbone off the ground and out of the work space. This explosion proof string light is equipped with an explosion proof outlet 5` from the last junction point, allowing operators to connect multiple units together end to end. Operators can daisy chain up to 20 units end to end in 120 volt or 35 units in 240 volt configurations. Up to 5 units in 24 volt AC/DC can be connected end to end. Stringer Energy Consumption Comparison Incandescent CFL LED Wattage 500 watts 130 watts 50 watts Amp Draw @ 120V AC 4.17 amps 1.09 amps 0.42 amps Amp Draw @ 277V AC 1.8 amps 0.47 amps 0.18 amps Amp Draw @ 12V DC 41.67 amps 10.84 amps 4.17 amps Amp Draw @ 24V DC 20.84 amps 5.42 amps 2.08 amps Lamp Life Expectancy 1,500 hours 8,000 hours 50,000 hours Color Temperature 2800K 4300K 6000K Operation cost per year(8hs/day @ 11c/kWh) $160.6 $41.76 $16.06 This stringer light set is Class 1, Division 1 rated for Groups C and D and Class II, Division 1 Groups F and G. This unit is multi-voltage and configured to operate on 120-277V AC or 12-24V DC, please choose your configuration below. Made in USA Quality Lamp Features 1. Federal Spec Cord.2. Explosion Proof.3. Total of (5) 10 watt LED Lamps.4. Non-sparking aluminum construction.5. UL Class 1 Div 1 Class 2 Div17. 120-277V AC or 12-24V DC Operation8. SOOW cable.9. Aluminum Hooks for Convenient Placement.10. Daisy Chain Connections. 50 watts of LED illuminationNon-sparking aluminum housingsLight weight mold T JuctionsCast aluminum guard prevent lamp or globe damageTemptered Soda-Lime Glass Lamp GlobeIntegrated lamp shock absorbers prevent drop damageSwivel hook for hanging and hands free operation14/3 SOOW Abrasion Resistant Cable Specifications / Additional Information EPL-SL-5-LED-E2E U.L. Ratings Listing: United States Class 1, Divisions 1 & 2, Groups C, D Dimensions- Each Lamp: L-16.5" Diam-5" Class 2, Divisions 1 & 2, Groups, F, G Total Watts: 50 Class 1, Zone 1, Group IIB Single Lamp Watt: 10 watts NEMA 4X Voltage: 120-277V AC or 12-24V DC Amps: 0.42 120V AC Mounting: Handheld / Hanging via Aluminum Hooks Special Orders- Requirements Wiring: 40` 14/3 SOOW Cable: 10` between lamps - 10` input whip - 5` output whip to EXP Outlet Contact us for special requirements Total Length: 60` Toll Free: 888-325-4448 Single Lamp Weight: 6 lbs Total Weight: 40 lbs E-mail: [email protected]