Larson Electronics Explosion Proof Emergency LED Light - C1D1/C2D1 - Powers On ONLY During Power Outages - 4' 2 Lamp

Made in the USAThe Larson Electronics EPL-EMG-48-2L-LED-113 Explosion Proof Emergency LED Light Fixture is NRTL Listed for United States and Canada approved Class I Division 1 & 2 and Class II Division 1 and 2 for areas where flammable chemical/petrochemical vapors exist or have the potential to exist. This failsafe explosion proof LED light has a T6 temperature rating and carries a paint spray booth light certification, making it ideal for applications such as paint booths, oil rigs, offshore applications, petrochemical, manufacturing, chemical storage, water treatment centers, and food processing plants. This emergency only fixture powers both lamps on when power is lost and shuts both lamps off when power is restored.This 4 foot long, 2 LED tube, explosion proof emergency ONLY light fixture is ideal for use in hazardous locations requiring powerful yet compact emergency lighting that will provide effective illumination in the event of power failure. This emergency light is designed to power both lamps on only when power is abnormally cut off. It does not operate as a standard area light and is intended for emergency lighting applications. The EPL-EMG-48-2L-LED-113 is equipped with Larson Electronics specially designed LED T-series bulbs which produce 7,000 lumens, resulting in 30% more foot candles of illumination at 8 feet as compared to standard T8 lamps when measured with an Extech light meter. Our LED-T series bulbs are visibly brighter than standard T8`s and have consistently surprised many of our customers with their unexpectedly high light output levels during emergency operation.We now offer our second generation LED tube lamps with this fixture which have increased this hazardous location light`s performance. This two lamp explosion proof LED linear emergency fixture is lighter in weight, has a slimmer profile, and produces more light than traditional explosion proof fluorescent fixtures. The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.With an integrated emergency ballast, this explosion proof LED light will operate for 90 minutes once the main electrical power to the light is severed. Once standard electrical power is restored, the emergency battery pack will be recharged. This fixture includes a test button in order to check operating accuracy under normal conditions.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division 2, Group A, B, C and D, and Class II, Division 1 and 2, Groups E, F and G environments where flammable or combustible gases, vapors, dusts, fibers, and flying exist or stand the potential to exist. This LED linear fixture is approved for use in confined spaces. Click here to read the NEC description for explosion proof and hazardous locations.Click Photo to EnlargeClick Photo to EnlargeThe included LEDT8-28W-V1 LED lamps have a 50,000+ hour service life, both of which result in extreme efficiency and greatly reduced maintenance costs. These fluorescent style LED lamps have internal drivers, eliminating external power components. The solid state design of the LED lamps give this fixture superior resistance to damage from vibration, extremes in temperature and a lamp service life over twice that of standard fluorescent bulbs. This second generation lamp is offered in 5600K cool white, 4500K natural white, and 3000K warm white. Our standard unit ships with 5600K unless different color temperature is specified.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. The LED assembly is mounted to the "tube" constructed from extruded aluminum, with a polycarbonate lens protecting the LEDs. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than fluorescent lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional fluorescent lighting.The 28 watt LED lamps produce 30% more illumination than standard T8 bulbs while offering lower amp draw and increased reliability. Each lamp produces 3,500 lumens at 125 lumens per watt, for a combined 7,000 total lumen light output. An EPL-EMG-48-2L-T8 explosion proof fluorescent light, with a combined total of 64 watts, draws 0.54 amps at 120 volts AC. This LED version of the same light, with a total of 56 watts, draws only 0.47 amps at 120 volts AC. The EPL-EMG-48-2L-LED-113 is universal voltage, not multi-tap, and operates on any voltage from 120V to 277V AC 50/60hz without any modifications. We also make a 12/24V AC/DC version for low voltage applications for AC or DC power.Energy Consumption ComparisonT5HO T8 LEDWattage 108 watts 64 watts 56 wattsAmp Draw @ 120V AC 0.90 amps 0.54 amps 0.47 ampsAmp Draw @ 220V AC 0.49 amps 0.29 amps 0.25 ampsAmp Draw @ 240V AC 0.45 amps 0.27 amps 0.23 ampsAmp Draw @ 277V AC 0.39 amps 0.24 amps 0.20 ampsAmp Draw @ 12V DC 9 amps 5.34 amps 4.67 ampsAmp Draw @ 24V DC 4.5 amps 2.67 amps 2.34 ampsLamp Life Expectancy 20,000 hours 24,000 hours 50,000 hoursOperation cost per year(12hs/day @ 12c/kWh) $56.77 $33.64 $29.43Our EPL-EMG-48-2L-LED-113 LED emergency only light fixture is NRTL Listed for United States and Canada approved for use in paint spray booths. Please note, according to the NEC, using threaded rigid pipe does not require additional seal offs with this fixture. An EYM and seal off is necessary for flex conduit or other non-rigid pipe implementations.Mounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting configurations.Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2" NPT junction box on one end, and a 1/2" NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires, completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.Suggested Applications: Paint spray booths, aircraft maintenance, oil drilling rigs, refineries, solvent and cleaning areas, gas processing plants, chemical manufacturing, waste treatment plants, gas processing plants.At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or message [email protected] for more information about our custom options tailored to meet your specific industry needs.Made in USA Quality Superior LED Benefits1. Each unit dielectrically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy4. No ballast box. No ballast to replace. We simply run the black wire to one end of the bulb and white wire to the other. 5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the "tap and knock off" method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.1. 50,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces energy use and prolongs life-spans of peripheral cooling units (A/C, refrigeration)5. 100% recyclable.6. No toxins-lead, mercury.7. No UV light, infrared radiation or CO2 emissions. 8. Qualifies buildings for LEED and other sustainable business certifications.9. Bright, even light maintains consistent color over time.10. Instant on/off - No flickering, delays or buzzing. 11. Very good color rendering.12. Vibration/impact resistant.13. Significantly cooler operation.14. Less frequent outages, higher output improves workplace safety.Specifications / Additional Information EPL-EMG-48-2L-LED-113 Explosion Proof Emergency Only LED Fixture Ratings/ApprovalsNRTL Listed for United States & Canada Class I Division 1, Groups C and D T6Dimensions: W-11.25" x L-52" x H-8.5 " Class I Division 2, Group A,B,C,DWeight: 60 Lbs Class II, Division 1 & 2, Groups E,F,GVoltage: Universal 120-277VAC 50/60 Hz NRTL Certified to UL 595 Marine Type (Saltwater)Total Watts: 56 watts (28 Watts Per Lamp) NRTL Certified to UL 844, UL 924Total Lumens: 7,000 (3,500 Per Lamp) NRTL Certified to UL 1598 Marine TypeLumens on Battery Power: 3,500 (1 Lamp) Certified Canadian StandardsLED Lamp Life Expectancy: 50,000+ Hours Listed for Paint Spray BoothsLuminous Efficacy: 125 Lumens per Watt California Title 24 CompliantColor Temp: 5600K, 4500K, 3000K IP67 Rated - WaterproofColor Rendering Index: >80 T6 Temperature RatingBeam Angle: 150¡ NEMA 4XPower Efficiency: 90% LEL Listed LED LampsPower Factor: >0.95 Approved for Confined SpacesBattery AC Input Voltage: 120/277V AC 60Hz Silicone FreeBattery AC Input Current: 90 mA Factory Sealed FixtureBattery AC Input Power Rating: 9.5W Failsafe LightingBattery Output Current: 120V @ 165mA - 277V @ 72mA Emergency Battery BackupIllumination Time: 90+ Minutes 90+ Minute RuntimeBattery Type: High Temp, Maintenance Free, Nickel Cadmium ABS ApprovedBattery Lifespan: 7 to 10 Years Made in the USABattery Charge Current: 250 mA Switch Leg for Powering Light On/OffBattery Recharge Time: 24 Hours Emergency ONLY OperationAmbient Operating Temp Range:0¡C to +50¡C Operating Temp Rating: T6 Rated Minimum Operating Temp: 0¡C Maximum Case Temp: +50¡C Housing Material: Cast Aluminum End Caps & Battery Enclosure, Aluminum Reflectors - Copper Free Lens Material: Hardened Borosilicate Glass Tubes Gasket Material: Buna Rubber O-Rings Special Orders- RequirementsMounting: Surface Standard - Pendant Optional Contact us for special requirementsWiring Hub: 1/2" NPT Toll Free: 1-800-369-6671Intl: 1-903-270-1187?E-mail: [email protected]