Larson Electronics C1D2 Hazloc Pivoting LED Light - 4' (2) Lamps - 2 Hours of Emergency Backup - Failsafe LED Rig Light

The Larson Electronics HAL-EMG-48-2L-LED-BMSW-2HR Hazardous Area LED Light Fixture with Emergency Failsafe Battery Backup provides powerful illumination in combustible facilities. Equipped with a T4A temperature rating, the LED light is ideal for hazardous locations where flammable chemical/petrochemical vapors may be occasionally encountered. In emergency mode, the 48-watt unit operates for 120 minutes at 1,350 lumens (single lamp).The HAL-EMG-48-2L-LED-BMSW-2HR fixture is a 4 foot long, 2 lamp Class I, Division 2 Groups A, B, C and D hazardous area LED light that takes the reliability and efficiency of a fluorescent fixture and adds longer lamp life and efficiency with high output LEDs. This 48-watt fixture is T4A temperature rated and comes standard with our high powered 24-watt LED lamps. The lamps are protected by a powder coated aluminum frame and shatter and heat resistant clear acrylic lens secured with eight zinc coated steel draw latches.The fixture is constructed of copper free sheet aluminum and powder coated. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture can be configured to run on 120 to 277V AC as well as 12-24V DC. This hazardous location LED fixture is Class I, Division 2 rated and meets USCG specs. The HAL-EMG-48-2L-LED-BMSW-2HR is weatherproof and provides operators in hazardous locations with a highly efficient, reliable and affordable lighting solution for open areas where flammable chemicals and vapors may occasionally be present.Click Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeThis light works, mounts and is wired like our HAL-48-2L-LED-BMSW explosion proof light fixtures. The main difference is that we add a battery backup unit that adds emergency light functionality to the fixture. This hazardous area emergency light will run one lamp at 120 minutes after power is lost at 1,350 lumens. The light recharges the battery once electrical power is restored.We have eliminated the ballast normally associated with fluorescent fixtures which reduces overall weight, increases lamp life to an extreme 50,000 hours and helps this LED fixture maintain a T4A temperature rating. The solid state design of the included LED lamps give this fixture superior resistance to damage from vibrations and extremes in temperature as well as a lamp service life over twice that of standard T8 bulbs. The 24-watt LED lamps produce more illumination than standard T8 bulbs, but draw only 3/4 of the current. The current generation of Larson Electronics LED T-series style bulbs produce 15% more light than standard T8 bulbs. This fixture is universial-voltage capable (not multi-tap) and works on the following voltages: 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ, 277 Volts 60 HZ. We also make a 12-24V DC version for low voltage applications (-LV suffix). Our HAL-EMG-48-2L-LED-BMSW-2HR LED light fixture is both NRTL Listed for U.S. and Canada.Energy Consumption ComparisonT5HO T8 LEDWattage 108 watts 64 watts 48 wattsAmp Draw @ 120V AC 0.9 amps 0.54 amps 0.4 ampsAmp Draw @ 277V AC 0.39 amps 0.24 amps 0.18 ampsAmp Draw @ 12V DC 9 amps 5.34 amps 4 ampsAmp Draw @ 24V DC 4.5 amps 2.67 amps 2 ampsLamp Life Expectancy 20,000 hours 24,000 hours 50,000 hoursColor Temperature 5000K / 4100K 4100K 5300KOperation cost per year(8hs/day @ 11c/kWh) $34.69 $20.56 $15.42Standard Surface Mount Brackets: Each L bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two bolts on either side of the bracket. The bolts act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be pivoted by loosening the cap screws that hold the bracket to the mounting peg. This fixture allows 45 degrees of pivot from the 90 degree point.At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs. Specifications / Additional Information HAL-EMG-48-2L-LED-BMSW-2HR Hazardous Area LED Light RatingsNRTL Listed for United States & Canada Class I, Division 2 Groups A,B,C,DDimensions: 51.1"-L x 7.09"-W x 8.65"-H NRTL Certified to UL 844Lamp Technology: LED NRTL Certified to UL 1598A Marine TypeLamp Qty: (2) 4` LED Lamps Listed for CanadaWeight: 27.8 Lbs T4A Temperature RatingTotal Watts: 48W Meets USCG SpecsVoltage: Universal 120-277V AC 50/60Hz California Title 24 CompliantLow Voltage (Optional): 12-24V DC Lumens: - Efficiency: 90 Lm/W LED Lamp Life Expectancy: 50,000+ Hours Color Temperature: 5300K Color Rendering Index: 75 Power Efficiency: - Power Factor: - Beam Angle: 150¡ Lighting Configuration: Flood Battery Type: High Temperature Rated Nickel Cadmium Battery Runtime: 120 Minutes Amps: 0.4A @ 120V, 0.2A @ 240V, 0.173A @ 277V Special Orders- RequirementsOperating Temp Range: -40¡C to +50¡C Contact us for special requirementsTemperature Rating: T4A Phone: 1-214-616-6180Materials: Sheet Aluminum Housing, Acrylic Lens Toll Free: 888-325-4448Mounting: Back Mount Swivel Bracket Fax: 1-903-498-3364Wiring Hub: 1/2" or 3/4" Threaded E-mail: [email protected]