Larson Electronics 25KVA Power Distribution Panel - 480V to 120/240V 1PH - (14) Receptacles - 30' 2/4 Type W Cord

Made in Texas The Larson Electronics MPD-480V-2X60-25KVA-10X120.20-2X240.30 power distribution substation provides three phase 480V electrical current to single phase 120/240VAC. This unit provides operators the ability to safely tap into and distribute 480VAC power from a variety of sources including generators and direct grid power. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO POWER DISTRIBUTION PANELS, TRANSFORMERS, OR SUBSTATIONS* Portable Power Distribution Purpose and Use: The MPD-480V-2X60-25KVA-10X120.20-2X240.30 portable power distribution system gives operators the ability to power their 480V and 120/240V equipment from a single system. On the primary side, operators connect 480 volt using a 30` 2/4 Type W cord and to two 460R7W receptacles for 480V equipment. On the secondary side, operators connect to two L6-30R receptacles for 240V equipment and to ten duplex receptacles for 120V equipment. All receptacles are protected by weatherproof covers. Operation: A 30` 2/4 Type W cable brings three phase 480V power to the NEMA 3R 150-amp 480V three phase primary panel, which contains three 3-pole 60-amp circuit breakers and two 60-amp 480V 460R7W receptacles, and passes 480V three phase through to the transformer. The NEMA 3R 25KVA transformer converts 480V single phase power to 120/240V single phase and passes the current to the secondary side. The secondary side of the transformer feeds a NEMA 3R 100-amp 120/240V single phase secondary panel. This secondary side contains two 2-pole 30-amp 250V breakers protecting two 30-amp 250V L6-30R receptacles and ten 1-pole 20-amp 125V breakers protecting ten 20-amp duplex 125V GFCI receptacles. Protective Construction: Unlike many portable power distribution boxes made of plastic and utilizing thin gauge, low grade metals in their construction, this unit is designed for serious use and is ruggedly constructed to withstand demanding conditions and heavy duty industrial applications. The transformer and load assembly is mounted on a 3/16" thick carbon steel mounting platform and the load center/distribution assembly is mounted to the standard 2" x 2" x 1/8" square carbon steel tubing frame, resulting in an extremely stable, durable and well protected power distribution platform. This model is equipped with forklift skid pockets, locking casters, and a top located lifting eyelet which allows easy lifting with cable or chain hooks. This can be replaced for an additional cost with stainless steel, hot dip galvanized steel, or aluminum depending on the customer’s needs. Larger units are available upon request and can be equipped with skids or trailer mounted. Certification: Larson Electronics is a UL 1640 panel shop and certified to build portable power distribution systems. All units are built in accordance to NFPA 70 (National Electric Code) and certified to UL 1640. All equipment is NEMA 3R rated for indoor and outdoor use and provide a degree of protection against dirt, water, and ice. NEMA 4 and NEMA 4X equipment can be equipped upon request. Grounding: Transformer is grounded to the frame and we provide a grounding lug on the frame for the earth ground. ~Please check all motor loads for dual rated motors that will work 208 or 240.~ Applications: This power distribution system is ideal for indoor or outdoor use and applications including but not limited to, construction sites, plant maintenance, plant turnarounds, shows, exhibits, and shipyard operations. These power distribution systems are popularly used in applications where external power sources are often necessary. We also offer class rated transformers for use within explosion proof and hazardous location environments. Custom Built Systems Available: Larson Electronics is a manufacturer and we can build portable power distribution systems to your specifications. Although we carry several models of portable power distribution systems in stock, we can deliver custom ordered units almost as quickly as our prebuilt units. If this model does not meet your needs, please contact us at 888-325-4448 [email protected] to discuss your specific requirements. Specifications / Additional Information MPD-480V-2X60-25KVA-10X120.20-2X240.30 Power Distribution Ratings Line-In Cord: 30` 2/4 Type W Cord Max OCP Primary: 60A @ 480V Line-In Cord Cap: Customer Provided Max OCP Secondary: 100A @ 240V Primary Voltage: 480VAC 3PH UL 1640 Portable Power-Distribution Equipment Primary Panel: 150A 480V 3PH Panel N3R NEMA 3R Indoor / Outdoor Use Primary Breakers: (3) 60A 3P [480V] Made in the USA Primary Receptacles: (2) 60A 460R7W [480V] Strain Relief Connector Primary Protection: Circuit Breakers, Weatherproof Covers Transformer: 25KVA 480V to 120/240V 1PH N3R Secondary Voltage: 120/240VAC 1PH Secondary Panel: 100A 120/240V 1PH Panel N3R Secondary Breakers: (2) 30A 2P [250V], (10) 20A 1P [125V] Secondary Receptacles: (2) 30A L6-30R [250V], (10) 20A Duplex GFCI [125V] Special Orders- Requirements Secondary Protection: Circuit Breakers, Weatherproof Covers Contact us for special requirements Form Factor: Square tube frame, skid pockets, top pick eye & 8” locking casters Toll Free: 888-325-4448 Frame Materials: Powder coated steel frame Intl: 1-214-616-6180 Dimensions: 34” X 44” X 58” Fax: 1-903-498-3364 Weight: 600 pounds E-mail: [email protected] Larson Electronics manufactures a wide variety of custom power distribution systems. The pictures displayed for this unit are a general representation of form factor and may not accurately represent this exact configuration in every detail due to being custom builds. The specifics for this configuration are listed in the specification table and one-line diagram. *All grounding shall comply with state and local codes and meet the minimum requirements of the National Electronic Code section 250* Scroll Down to Purchase