Larson Electronics 18 Watt LED Flood Light - Magnetic Base - 1400 Lumens - Six 3-Watt LEDs - 10-32 Volt DC - IP67 Water

The IL-LED-18-M LED Light Bar offers high light output from a compact form factor and with its magnetic base that has 100 lbs of gripping power and two pin Deutsch connecter, is ideal for a wide range of uses including heavy equipment, boating, vehicle, military, law enforcement and industrial manufacturing applications. This unit produces a 1400 lumen light output with very low amp draw, 30,000 hour service life and 10 to30 volt compatibility which provides operators with a compact and powerful LED lighting solution. The IL-LED-18-M LED light bar from Larson Electronics produces 1400 lumens of bright light while drawing only 18 watts @1.4 amps from a 12 volt electrical system. Sixhigh outputthree watt LEDs producing 233 lumens each are arranged in rows and paired with high purity optics to produce a wide 60 degree flood beam. These LED light bars are IP67 waterproof, sealed against intrusion by dust and dirt and very ruggedly constructed to withstand the most demanding environments, conditions and applications. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or “duty cycle” accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each LED based upon the LED’s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 100% capacity without overheating or visible loss of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually on or off. Durability: As well as unparalleled heat control, the IL-LED-18-MLED light bar from Larson Electronics also offer IP67 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40 degrees Celsius to 85 degrees Celsius, are waterproof to three meters and resist ingress of dust, dirt and humidity. The housings are formed from extruded diecast aluminum and the lenses are unbreakable polycarbonate. We recommend these LED lights for high humidity climates, very cold areas and rough saltwater conditions. They are also applicable to environments where equipment is used in one temperature extreme and stored in another temperature extreme. Wiring: The IL-LED-18-M comes with a two pin Deutsch connector 16` Cigarette Plug. We also offer 16` Straight Cord, 21` Ring Terminals, and 21` Battery Clamps. 16ft Coil Cord w/Cigarette Plug 21ft Cord with Ring Terminals 16ft Cord w/Battery Clamps 16ft Cord with Cigarette Plug Click Images to Enlarge Mounting: The 100 lbs Gripping power magnet mounting design allows for easy placement and removal. This mounting system includes a power cord with a cigarette plug connector whichmakes this unit ideal for vehicle and equipment lighting applications where the unit can simply be attached or removed as needed. Please note, the magnetic base on this unit increases the units overall height. Note: Most Larson Electronics LEDLB, LEDP3W, LEDP10W, and LED10W series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. Specifications / Additional Information IL-LED-18-M LED Light Bar Lamp Type: CREE XLamp XR-E¨ LED IP 67 Waterproof Rate Dimensions: 4 3/8"-L2 1/2"-H 2 1/4"-D Watts: 18 Lumens: 1400 Wiring: Deutsch IPD / LADD DT04-2P connector Cord lengths/types: 16` Cig Plug, 16` Straight Cord, 21` Ring Terminals, or 21` Battery Clamps Amps: 1.4 (on 12 volts) Mounting: Magnetic Base W/ 100 lbs of gripping power LED Light Color: 6000K Lighting Configuration:60¡ Flood Special Orders- Requirements LED Life Expectancy:30,000 hours Contact us for special requirements Materials: Aluminum Housing, Polycarbonate Lens, Magnetic Base Toll Free: 888-325-4448 E-mail: [email protected] 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement. Scroll Down to Purchase-