EiKO PSC-BL-I-FM-DC0 Stand-alone TruBlu PIR Motion Sensor, 12-24V, 1/2in Knock-Out, 0-10V

Overview:

• Quad Element PIR sensor
• 0-10V configurable output: set to 0% (OFF)*, 10%, 25% or 50%dimming
• Day/Night Photocell
• Time delay 1 adjustable 5 sec to 30 min
• Time delay 2 adjustable 10 sec to Infinity
• LED Motion indicator
• Active High/Low outputs for Relay drive
• Mounting height up to 40ft (12.2m)
• 360Deg. coverage pattern
• Bluetooth add-on enables remote sensor programming with greater customization of dimming levels, and time delays

Applications:

The PSC-BL-I-FM-DC0 uses PIR Motion Detector Architecture and Quad Element passive infrared (PIR) technology for improved detection coverage for ceiling mount, high bay, and low bay applications.

The PSC-BL-I-FM-DC0 is a Class 2 Device designed to satisfy new CA Title 24 requirements for bi-level dimming of lighting fixtures. Using a 0-10V signal, the sensor is capable of dimming lighting loads down to 0% *, 10%, 25%, or 50%.

The sensor is suitable for a variety of indoor and outdoor** applications. It supports fixture and ceiling mounts up to 40ft (12.2m) high. Both sensor and power pack are rated for use in temperatures ranging from -30Deg. to 70Deg. C and relative humidity from 90 to 95% at 30Deg. C.

0-10V: 100mA to drive up to 50 LED sink drivers on 0-10V output. High Vin-2.5V 100mA source Low 100mA sink current.

*For dim to off, Pacific PSC-AC-PP-200 Power Pack or LED dimming driver capable of dimming to off is required.

**PSC-BL-I-FM-DCO is outdoor use at the Sensor Collar part only. Side and Bottom Mount IP65 enclosure available for completely outdoor sensor option.

Sensor Operation:

End users can program length of time delays, motion detection sensitivity, photocell on/off, and other settings using a series of dipswitches and trimpots. Simply remove the lens to gain access.

Bi-level Dimming**:

0-10V bi-level dimmer connects to 0-10V control on the LED driver. When motion is detected the sensor will bring lighting up to 100% lumen output. When no motion is detected for the length of TD1, the sensor will send a signal to dim lighting to a specific level set by the end-user. If no motion is detected for the length of TD2, the sensor will send a signal to shut off the light.

Relay Control:

Two additional High and Low control outputs can be used to trigger relays or other control circuitry.

Bluetooth Smart and Bluetooth Mesh:

The Bluetooth Low Energy (BLE) enabled version pairs with an Android or iOS application to allow initial setup and subsequent sensor adjustments, beyond what the analog controls on the sensor can offer. The mobile application enables adjustment of sensor parameters such as time delay, dim level, sensitivity, daylight detection, and more. Additionally, features such as parameter profiles, manual dim control, and real-time feedback from the sensor can speed up configuration and provide custom user control. The Bluetooth Smart enabled sensors support mesh networking through a variety of software and wireless platforms.

Accessories:

Power Pack:

The PSC-BL-I-FM-DC0 operates on 12-24VDC input and requires a separate power pack such as the PacWave PSC-ACPP-200/300/400.

This power pack incorporates a high current relay and a high voltage transformer which can accept universal input (100-305VAC).

Alternatively, the sensor can also operate with a driver that has an auxiliary output (12V).

Fresnel Lens:

LBL: 8-30ft (2.4-9.1m) Fresnel Low bay lens HBL: 20-40ft (6.1-12.2m) Fresnel High bay lens

**The sensor will dim the light if motion is not detected for the first time delay (TD1) and shut off the light if motion is not detected for the second time delay (TD2). TD2 will only count down after TD1 has expired and the light has dimmed. If motion is detected during TD2, the light will return to full output, and TD1 will restart.

If using a power pack, the sensor will tell the power pack to shut off the driver after TD2 expires to turn off the light. If using a dimming driver without a power pack, the sensor will try to dim down to 0% upon expiration of TD2

Since one trimpot configures both TD1 and TD2, a fixed TD2 is set to each value of TD1.

Note:

*The absolute range of the sensor is subject to variation because of different types of clothing, backgrounds, and ambient temperature. Therefore, ensure that the lens is properly oriented along routes with expected traffic and conduct testing along those routes.

**Bluetooth versions enable adjustment of sensor parameters such as time delay, dim level, sensitivity, ON/OFF daylight detection, and more.

***Bluetooth Range is highly dependent on the integration of fixtures, surrounding environment and conditions. It is recommended to conduct testing for range accuracy.

****If TD1 is set to 10 min, TD2 will never expire. So the light will remain at the dim level for as long as motion is not detected.

Specification:

• Control Type: Wireless Control
• Voltage: 12-24VDC
• Current (mA): 50mA
• Communication Frequency: 2.4GHz
• Detection Frequency (new): 49-65ft
• Sensor Mounting Height: 20-40ft
• Sensor Technology: PIR
• Wireless Technology: Bluetooth SIG Mesh
• App Name: Silvair
• Sensor Installation Type: Z10 Twist-lock
• Daylight Harvesting: Yes
• Daylight Threshold: Yes
• Network Lighting Control: Yes
• Relay On/Off: Yes
• Bi-Level Dimming: Yes
• Dimming Protocol: 0-10V