Larson Electronics Dimmable Explosion Proof LED Paint Spray Booth light - Class 1 & 2 Div 1 - T6 - 5,750 Lumens

Made in the USAThe Larson Electronics EPL-48-2L-LED-D Explosion Proof Dimmable LED Light Fixture is NRTL Listed for United States and Canada and rated Class 1 Division 1 & 2 and Class 2 Division 1 and 2 for areas where flammable chemical/petrochemical vapors exist or have the potential to exist. This explosion proof LED light has a T6 temperature rating and carries a paint spray booth light certification, making it ideal for applications such as paint booths, oil rigs, offshore applications, petrochemical, manufacturing, chemical storage, water treatment centers, and food processing plants.This four foot, two lamp dimmable LED fixture is ideal for operators seeking a top quality explosion proof light that will reduce operating costs, improve lighting quality and reduce downtime incurred from frequent servicing intervals. The EPL-48-2L-LED-D is equipped with Larson Electronics’ specially designed dimmable LED T-series bulbs which produce 5,750 lumens.This two lamp explosion proof LED linear fixture is lighter in weight, has a slimmer profile, and produces more light than traditional explosion proof fluorescent fixtures. The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division 2, Group A, B, C and D, and Class II, Division 1 and 2, Groups E, F and G environments where flammable or combustible gases, vapors, dusts, fibers, and flying exist or stand the potential to exist. This LED linear fixture is approved for use in confined spaces. Click here to read the NEC description for explosion proof and hazardous locations.Click Photo to EnlargeClick Photo to EnlargeWe have eliminated the ballast box normally associated with explosion proof fluorescent fixtures which reduces overall weight and overall complexity of installation. There is no ballast in this unit and the included dimmable LEDT8-48-D LED lamps have a 50,000+ hour service life, both of which result in extreme efficiency and greatly reduced maintenance costs. These fluorescent LED lamps have internal drivers, eliminating external power components. The solid state design of the LED lamps give this fixture superior resistance to damage from vibration, extremes in temperature and a lamp service life over twice that of standard fluorescent bulbs. This second generation lamp is offered in 5600K cool white, 4500K natural white, and 3000K warm white. Our standard unit ships with 5600K unless different color temperature is specified.These dimmable 23 watt LED tubes operate with voltage dimming switches such as the Leviton 6633-PLW. Lumen output is 125 lumens per watt for a total of 2,875 lumens per bulb. While fluorescent lamps are omni-directional and illuminate 360¡, the LED style replacement lamps are directional and offer a 160¡ beam spread. This allows for directed illumination where it is needed and not wasting light via reflectors or or over illuminating areas. This dimming LED tube uses electronic silicon control dimming. We have tested these lamps on all Lutron and Leviton electronic dimmers, such as the Leviton 6633-PLW. When using electronic dimmer switches, fixtures equipped with the LEDT8-48-D LED bulb will dim from 0% up to 100% via the user provided dimming switch. Please note: the dimmer switch must be installed outside the hazardous environment or use an explosion proof dimmer switch. This fixture will not work on voltage outside of the 90-132V AC range and internal damage may occur when higher voltage is applied to the lamps.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. The LED assembly is mounted to the "tube" constructed from extruded aluminum, with a polycarbonate lens protecting the LEDs. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than fluorescent lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional fluorescent lighting.The 23 watt LED lamps produce 30% more illumination than standard T8 bulbs while offering lower amp draw and increased reliability. Each lamp produces 2,875 lumens at 125 lumens per watt, for a combined 5,750 total lumen light output. An EPL-48-2L-T8-D explosion proof fluorescent light, with a combined total of 64 watts, draws 0.54 amps at 120 volts AC. This LED version of the same light, with a total of 46 watts, draws only 0.38 amps at 120 volts AC. The EPL-48-2L-LED-D operates on any voltage from 120V or 277V AC 50/60hz without any modifications.Energy Consumption ComparisonT5HO T8 LEDWattage 108 watts 64 watts 46 wattsAmp Draw @ 120V AC 0.90 amps 0.54 amps 0.38 ampsAmp Draw @ 277V AC 0.39 amps 0.24 amps 0.17 ampsLamp Life Expectancy 20,000 hours 24,000 hours 50,000 hoursOperation cost per year(12hs/day @ 12c/kWh) $56.77 $33.64 $24.18Please note: operation costs are calculated with the light fixture at 100% illumination. When dimming the light fixture below 100%, electrical consumption will be lowerOur EPL-48-2L-LED-D LED light fixture is NRTL Listed for United States and Canada and approved for use in paint spray booths. Please note, according to the NEC, using threaded rigid pipe does not require additional seal offs with this fixture. An EYM and seal off is necessary for flex conduit or other non-rigid pipe implementations.Mounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting configurations.Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2” NPT junction box on one end, and a 1/2” NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires, completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.Suggested Applications:Paint spray booths, aircraft maintenance, oil drilling rigs, refineries, solvent and cleaning areas, gas processing plants, chemical manufacturing, waste treatment plants, gas processing plants.Made in USA Quality Superior LED Benefits1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy4. No ballast box. No ballast to replace. We simply run the black wire to one end of the bulb and white wire to the other. 5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.1. 50,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces energy use and prolongs life-spans of peripheral cooling units (A/C, refrigeration)5. 100% recyclable.6. No toxins-lead, mercury.7. No UV light, infrared radiation or CO2 emissions.8. Qualifies buildings for LEED and other sustainable business certifications.9. Bright, even light maintains consistent color over time.10. Instant on/off – No flickering, delays or buzzing.11. Very good color rendering.12. Vibration/impact resistant.13. Significantly cooler operation.14. Less frequent outages, higher output improves workplace safety. Specifications / Additional Information Specifications / Additional InformationEPL-48-2L-LED-D Explosion Proof LED Fixture Ratings/ApprovalsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and D T6Dimensions: W-11.25" x L-52" x H-8.5 " Class 1 Division 2, Group A,B,C,DWeight: 45 Lbs. Class 2, Division 1 & 2, Groups E,F,GVoltage: 120V or 277V NRTL Certified to UL 595 Marine Type (Saltwater)Total Watts: 46 watts (23 Watts Per Lamp) NRTL Certified to UL 844Total Lumens: 5,750 (2.875 Per Lamp) NRTL Certified to UL 1598 Marine TypeLED Lamp Life Expectancy: 50,000+ Hours Certified Canadian StandardsLuminous Efficacy: 125 Lumens per Watt Listed for Paint Spray BoothsColor Temp: 5600K, 4500K, 3000K California Title 24 CompliantColor Rendering Index: >80 IP67 Rated - WaterproofBeam Angle: 150¡ T6 Temperature RatingPower Efficiency: 90% NEMA 4XPower Factor: >0.95 LEL Listed LED LampsAmbient Operating Temp Range:-30¡ C to +85¡C Approved for Confined SpacesOperating Temp Rating: T6 Rated Silicone FreeMinimum Operating Temp: -30¡C Factory Sealed FixtureMaximum Case Temp: +90¡C Made in the USAHousing Material: Cast Aluminum End Caps, Aluminum Reflectors - Copper Free Lens Material: Hardened Borosilicate Glass Tubes Gasket Material: Buna Rubber O-Rings Special Orders- RequirementsMounting: Surface Standard - Pendant Optional Contact us for special requirementsWiring Hub: 1/2" NPT Toll Free: 1-800-369-6671Intl: 1-903-270-1187E-mail: [email protected]