Larson Electronics 48W Explosion Proof LED Light - Blue or Red - 4ft 2-Lamp - Class 1, Div. 1 - Blackout Light

The Larson Electronics EPL-48-2L-LED-C Explosion Proof LED Light Fixture with red or blue lamps is United States and Canada approved Class I, Division 1 & 2 and Class II, Division 1 and 2 for areas where flammable chemical/petrochemical vapors exist or have the potential to exist. This 4` explosion proof LED light has a T6 temperature rating and carries a paint spray booth light certification, making it ideal for applications such as paint booths, oil rigs, offshore applications, petrochemical, manufacturing, chemical storage, water treatment centers, and food processing plants. This two foot, two lamp LED fixture is ideal for operators seeking a top quality explosion proof light that will reduce operating costs, improve lighting quality and reduce downtime incurred from frequent servicing intervals. The 48-watt lighting system is equipped with Larson Electronics’ specially designed LEDST-5 bulbs, with two blackout red or blue LED lamp with 6 individual LED light strips in each side. Each lamp has individual leads to be powered separately. Our LED-T series bulbs are visibly brighter than standard F17/T8`s and have consistently surprised many of our customers with their unexpectedly high light output levels. These LED lamps produce 30% more illumination than standard T8 bulbs while offering lower amp draw and increased reliability. This LED light, with a total of 48 watts, draws only 0.4 amps at 120 volts AC. The EPL-48-2L-LED is universal voltage, not multi-tap, and operates on any voltage from 120V to 277V AC 50/60hz without any modifications. We also make a 10-30V DC version for low voltage applications for AC or DC power. This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division 2, Group A, B, C and D, and Class II, Division 1 and 2, Groups E, F and G environments where flammable or combustible gases, vapors, dusts, fibers, and flying exist or stand the potential to exist. This LED linear fixture is approved for use in confined spaces. Click here to read the NEC description for explosion proof and hazardous locations. We have eliminated the ballast box normally associated with explosion proof fluorescent fixtures which reduces overall weight and overall complexity of installation. There is no ballast in this unit and the included LED lamps have a 50,000+ hour service life, both of which result in extreme efficiency and greatly reduced maintenance costs. These fluorescent LED lamps have internal drivers, eliminating external power components. The solid state design of the LED lamps give this fixture superior resistance to damage from vibration, extremes in temperature and a lamp service life over twice that of standard fluorescent bulbs. This second generation lamp is offered in 600-675nm wavelength red or blue for the blackout lamp. Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current applied and emitting light. The LED assembly is mounted to the "tube" constructed from extruded aluminum, with a polycarbonate lens protecting the LEDs. With LED lights, there is no warm up time or cool down time before re-striking and provide instant illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than fluorescent lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional fluorescent lighting. Energy Consumption Comparison T5HO T8 LED Wattage 48 watts 34 watts 28 watts Amp Draw @ 120V AC 0.40 amps 0.29 amps 0.23 amps Amp Draw @ 220V AC 0.22 amps 0.16 amps 0.13 amps Amp Draw @ 240V AC 0.20 amps 0.14 amps 0.12 amps Amp Draw @ 277V AC 0.18 amps 0.13 amps 0.10 amps Lamp Life Expectancy 20,000 hours 24,000 hours 50,000 hours Operation cost per year(12hs/day @ 12c/kWh) $25.23 $14.87 $14.72 Our EPL-48-2L-LED-C LED light fixture is U.S. and Canada approved for use in paint spray booths. Please note, according to the NEC, using threaded rigid pipe does not require additional seal offs with this fixture. An EYM and seal off is necessary for flex conduit or other non-rigid pipe implementations. Mounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting configurations. Surface Mount (Standard) Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. Pendant Mount (Optional) 3 Conduit Positions Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2” NPT junction box on one end, and a 1/2” NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires, completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the fixture. Suggested Applications: Paint spray booths, aircraft maintenance, oil drilling rigs, refineries, solvent and cleaning areas, gas processing plants, chemical manufacturing, waste treatment plants, gas processing plants. At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs. Specifications / Additional Information EPL-48-2L-LED-C Explosion Proof RatingsDimensions: W-11.25" x L-52" x H-8.5" Class I, Division 1, Groups C and DWeight: 45 lbs Class I, Division 2, Group A,B,C,DVoltage: Universal 120-277V AC 50/60 Hz or 10-30V DC Class II, Division 1&2 Groups E,F,GTotal Watts: 48W (24W per Lamp) NRTL Certified to UL 595 Marine Type (Saltwater)Total Lumens: 3,000 NRTL Certified to UL 844LED Lamp Life Expectancy: 50,000+ Hours NRTL Certified to UL 1598 Marine TypeLuminous Efficiency: 125 Lumens per Watt Paint Spray Booth ApprovedColor: 600-675Nm (Red) or 420-440Nm (Blue) California Title 24 CompliantColor Rendering Index: >80 IP67 Rated - WaterproofBeam Angle: 150¡ T6 Temperature RatingPower Efficiency: 90% NEMA 4XPower Factor: >0.95 LEL Listed LED LampsAmp Draw: 0.4A @ 120V AC, 0.173A @ 277V AC Approved for Confined SparesAmbient Operating Temp Range:-35¡ C to +55¡C Silicone FreeOperating Temp Rating: T6 Rated Factory Sealed FixtureMinimum Operating Temp: -35¡C Maximum Case Temp: +90¡C Special Orders- RequirementsHousing Material: Cast Aluminum End Caps, Aluminum Reflectors - Copper Free Contact us for special requirementsLens Material: Hardened Borosilicate Glass Tubes Phone: 1-214-616-6180Gasket Material: Buna Rubber O-Rings Toll Free: 1-800-369-6671Mounting: Surface Standard - Pendant Optional Fax: 1-903-498-3364Wiring Hub: 1/2" NPT E-mail:[email protected]