Larson Electronics 25KVA Temporary Power Distribution - 480V to 120/240V 1PH - (2) L6-30R (12) 5-20R GFCI Duplex

Made in Texas The Larson Electronics MGL-480V-25KVA-20X120.20A-2X240.30A-20C temporary power distribution system converts single-phase 480V AC electrical current into 120/240V AC single phase. This unit provides operators the ability to safely tap into and distribute 480V AC power from a variety of sources including generators and direct grid power. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO POWER DISTRIBUTION PANELS, TRANSFORMERS, OR SUBSTATIONS* Portable Power Distribution Purpose and Use: The MGL-480V-25KVA-20X120.20A-2X240.30A-20C portable power distribution system gives operators the ability to power their 120 volt equipment from a single system. On the primary side, operators connect 480V using a 20` #8 Type W cable. On the secondary side, operators connect to two L6-30R receptacles for 240V equipment and to twenty GFCI duplex receptacles for 120V equipment. All receptacles are equipped with weatherproof covers. Operation: A 20` #8 Type W cable brings single-phase 480V power to the NEMA 3R 60-amp, 480V single phase primary disconnect, which contains two 60-amp time delay fuses, and passes 480V single phase power through to the transformer. The NEMA 3R 25 KVA transformer converts 480V to 120/240V single phase and passes the current to the secondary side. The secondary side of the transformer feeds a NEMA 3R 120/240V single phase 125-amp main lug only panel. This secondary side contains two 30-amp, 2-pole, 250V breakers protecting two 30-amp, 250V L6-30R receptacles, and ten 20-amp, 1-pole, 125V breakers protecting twenty 20-amp, 5-20R, 125V duplex GFCI receptacles. Protective Construction: The transformer and load center/distribution assembly is mounted to a powder coated steel, dolly cart style frame, resulting in an extremely stable, durable, and mobile power distribution platform. Two run-flat rubber tires and a dolly cart style mounting platform provides easier substation mobility, and a center point lift point allows easy lifting with cable or chain hooks. This temporary power distribution solution can be modified to meet the needs of job-site receptacle requirements. Units are available up to 150 KVA and can be equipped with skids or trailer mounted. Certification: Larson Electronics is a UL 1640 panel shop and certified to build portable power distribution systems. All units are built in accordance to NFPA 70 (National Electric Code) and certified to UL 1640. All equipment is NEMA 3R rated for indoor and outdoor use and provide a degree of protection against dirt, water, and ice. NEMA 4 and NEMA 4X equipment can be equipped upon request. Grounding: Transformer is grounded to the frame and we provide a grounding lug on the frame for the earth ground. ~Please check all motor loads for dual rated motors that will work 208 or 240.~ Applications: This power distribution system is NEMA 3R rated and ideal for indoor/outdoor use and applications including but not limited to; construction sites, plant maintenance, plant turnarounds, shows, exhibits and shipyard operations. Larson Electronics is a manufacturer and as such can build portable transformer systems to your specifications. Although we carry several models of power distribution transformers, we can deliver custom ordered units almost as quickly as our prebuilt units. If this model does not meet your needs, please contact us at 888-325-4448 [email protected] to discuss your specific requirements. Specifications / Additional Information MGL-480V-25KVA-20X120.20A-2X240.30A-20C -Temporary Power Distribution Ratings Line In: 20` #8 Type W Cable Max Primary OCP: 60A @ 480V Primary Voltage: 480V AC 1PH Max PDU OCP: 60A @ 480V Primary Disconnect: 480V 60A 1PH N3R Fused @ 60A Max Secondary Output: 104.2A @ 240V Primary Protection: Time Delay Fuses, Disconnect UL 1640 Portable Power-Distribution Equipment Transformer: 25KVA 480V to 120/240V 1PH N3R NEMA 3R Indoor or Outdoor Use Secondary Voltage: 120/240V AC Made in the USA Secondary Panel: 125A 120/240V 1PH MLO N3R Secondary Breakers: (2) 30A 2P [250V], (10) 20A 1P [125V] Special Orders- Requirements Secondary Outlets: (2) 30A L6-30R [250V], (20) 20A 5-20R GFCI Duplex [125V] Contact us for special requirements Secondary Protection: Circuit Breakers, GFCI, Weatherproof Covers Toll Free: 888-325-4448 Form Factor: Powder Coated Steel Dolly Cart w/ Run Flat Tires Fax: 1-903-498-3364 Dimensions: W-40" X D-40" X H-48" Intl: 1-214-616-6180 Weight: 350 lbs E-mail: [email protected] Larson Electronics manufacture a wide variety of custom power distribution systems. The pictures displayed for this unit are a general representation of form factor and may not accurately represent this exact configuration in every detail due to being custom builds. The specifics for this configuration are listed in the specification table and one-line diagram. *All grounding shall comply with state and local codes and meet the minimum requirements of the National Electronic Code section 250* Scroll Down to Purchase