Larson Electronics Stainless Steel Fluorescent Light Fixture w/ Remote Ballast - Corrosion Resistant - Class 1 Div 2 Marine Applications

Made in the USAThe Larson Electronics HALSS-48-2L-EB-EB Hazardous Location Fluorescent Lighting Fixture is ETL approved Class 1 Division 2 Groups A, B, C and D - NRTL Certified to 1598A and is specifically designed to withstand high vibration locations and the rigors of wet and corrosive marine environments. This light fixture features a remote ballast designed for hot box applications.Click here to see the LED version of this light.The HALSS-48-2L-EB-EB hazardous location fluorescent light fixture is designed for use in wet areas and saltwater-marine environments where corrosion resistance is critical to equipment longevity and safety. This Class 1 Division 2 rated fixture is constructed of non-corrosive materials including a stainless steel housing, a poured in gasket for reliable sealing and an impact resistant acrylic diffuser. Corrosion resistant stainless steel latches secure the lamp cover to the housing and provide a firm lock against the poured in seal to prevent drips and water intrusion.This fixture is ETL 844 rated and Class 1 Division II, Groups A, B, C, D approved. The HALSS-48-2L-EB is also NRTL Certified to 1598A and 595 outdoor marine ratings and meets US Coast Guard specifications.Click Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeThis fixture is designed for heavy duty use in applications where intense vibration and corrosive environments may be encountered. Stainless steel construction, high impact acrylic lamp covers, and a Class 1 Division 2 ETL rating make this light ideal for hazardous locations that require illumination with above average dependability.Remote Ballast: This unit is designed for high temp operations commonly referred to as "hot box" applications. The fluorescent ballast is included but not wired up. Customers must take care of mounting ballast, commonly done in a ballast room, and run wire from the ballast to the lamp. This remote ballast allows the ballast to remain cool while the fixture itself is in a hot box application, extending the longevity of the ballast by not exposing it to heat which is the primary factor that shortens ballast lifespan.NOTE ON LAMPS: This fixture comes equipped with F54-T5/850/HO – 54 Watt lamps producing 5,000 lumens per bulb, a 5000 Kelvin color and a 20,000 hour rated service life. We offer F48-T12/HO – 4050 lumens per bulb, 12,000 hours life, 4100 Kelvin color and F32-T8/841 – 2950 lumens per bulb, 24,000 hours life, 4100 Kelvin color tubes as lamp options for this fixture. The HALSS-48-2L-EB has an electronic multi-voltage ballast and works with 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ and 277 Volts 60 HZ. 24 Volt models available on request for an additional $100 per unit charge.Standard Flange Brackets: Stainless steel bracket mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide flexibility in setting the angle of the fixture. Three through holes provide sufficient mounting for any environment.Suggested Applications: The HALSS-48-2L-EB is designed for marine wet and damp locations, where corrosion resistant fluorescent lights are required. This lamp is also ideal for locations where heavy vibratory conditions are present. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas, water treatment areas, processing plants and marine loading docks.Made in USA Quality Lamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface.3. Fixture housing constructed of 14 gauge stainless steel..4. Relamping done via stainless steel snap locking latches which allow the operator to remove the door and access the lamps.5. Lamp cover-diffuser constructed of high impact acrylic for corrosion resistance and lamp protection.6. 1/2 inch, threaded access hole for wiring conduit. F54-T5/850/HO – 54 Watt, 5000 lumens per bulb, 20,000 hours life, 5000 Kelvin color F48-T12/HO – 4050 lumens per bulb, 12,000 hours life, 4100 Kelvin color F32-T8/841 – 2950 lumens per bulb, 24,000 hours life, 4100 Kelvin color F48-T8/HO - 48 watt, 4000 lumens per bulb, 18,000 hours life, 4100 Kelvin color (Suffix -T8HO) Specifications / Additional Information HALSS-48-2L-EB Hazardous Location Lighting ETL RatingsETL Listing: United States Class 1 Division 2, Groups A, B, C, DDimensions: W-9 1/2" L-54 " H-6 3/4" NRTL Certified to UL 844Weight: 35 Lbs NRTL Certified to UL 595 outdoor marineTotal Watts: 108 watts* NRTL Certified to 1598A Marine Type (Salt water)Voltage: 120V-60hz 220V-50hz 240V-60hz 277V-60hz (24V on Request) Remote BallastTotal Lumens: STD-T5-HO Bulbs 10,000 Lamp Life Expectancy: STD-T5-HO Bulbs 20,000 Hours Efficiency: STD-T5-HO Bulbs 92 Lumens per Watt Operating Temp Range: T4C Rated -30 C to 70 CMinimum Operating Temp: -30 CMaximum Case Temp: 90 C Beam Angle: N/A Special Orders- RequirementsColor Temp: 5000K- T5-HO Bulbs Contact us for special requirementsMounting: Flange type stainless steel Toll Free: 888-325-4448Wiring Hub: 1/2 inch threaded Intl: 1-903-270-1187? E-mail: [email protected] US Coast Guard specifications.*Wattage totals are lamps only and may vary with different lamps.