Larson Electronics Stainless Steel Fluorescent Fixture w/ Emergency Ballast - Corrosion Resistant - Class I, Div. II

Made in the USA The Larson Electronics HALSS-EMG-48-2L Hazardous Area Fluorescent Light Fixture is ETL approved Class 1 Division 2 Groups A, B, C and D - 1598A listed and is specifically designed to withstand high vibration locations and the rigors of wet and corrosive marine environments. This fixture includes an emergency power backup providing 90 minutes of runtime in the event of power failure. The HALSS-EMG-48-2L hazardous area fluorescent light fixture is designed for use in wet areas and saltwater-marine environments where corrosion resistance is critical to equipment longevity and safety. This Class 1 Division 2 rated fixture is constructed of non-corrosive materials including a stainless steel housing, a poured in gasket for reliable sealing, and an impact resistant acrylic diffuser. Corrosion resistant stainless steel latches secure the lamp cover to the housing and provide a firm lock against the poured in seal to prevent drips and water intrusion. A specially designed ballast box is built in that adds emergency light functionality to the fixture. This hazardous location emergency light fixture will run one lamp at 900 lumens for 90 minutes after power is lost. The light recharges the battery once electrical power is restored. This fixture is UL 844 rated and Class 1 Division 2, Groups A, B, C, D approved. The HALSS-EMG-48-2L also carries a 1598A outdoor marine rating and meets US Coast Guard specifications. This fixture is designed for heavy duty use in applications where intense vibration and corrosive environments may be encountered. Stainless steel construction, high impact acrylic lamp covers, a Class 1 Division 2 ETL rating and an emergency battery backup make this light ideal for areas that require illumination with above average dependability. The HALSS-EMG-48-2L has an electronic multi-voltage ballast and works with 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ and 277 Volts 60 HZ. 24 Volt models available on request for an additional $100 per unit charge. Standard Flange Brackets: Stainless steel bracket mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide flexibility in setting the angle of the fixture. Three through holes provide sufficient mounting for any environment. Suggested Applications: The HALSS-EMG-48-2L is designed for marine wet and damp locations, where corrosion resistant fluorescent lights are required. This lamp is also ideal for locations where heavy vibratory conditions are present. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas, water treatment areas, processing plants and marine loading docks.< Made in USA Quality Lamp Options 1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface.3. Fixture housing constructed of 14 gauge stainless steel..4. Relamping done via stainless steel snap locking latches, which enable the operator to remove the door and access the lamps.5. Lamp cover-diffuser constructed of high impact acrylic for corrosion resistance and lamp protection.6. 1/2 inch, threaded access hole for wiring conduit. F32-T8/841 – 2950 lumens per bulb, 24,000 hours life, 4100 Kelvin color Specifications / Additional Information HALSS-EMG-48-2L Hazardous Location Emegerncy Light ETL Ratings ETL Listing: United States Class 1 Division 2, Groups A, B, C, D Dimensions: W-9 1/2" L-54 " H-6 3/4" 844 Weight: 35 Lbs 1598A Marine Type (Salt water) Total Watts: 64 watts Meets US Coast Guard specifications. Voltage: 120V-60hz 220V-50hz 240V-60hz 277V-60hz (24V on Request) Total Lumens: 5,900 Lamp Life Expectancy: 24,000 Hours Efficiency: 64 Lumens per Watt Operating Temp Range: T4C Rated -30 C to 70 C Color Temp: 14100K Special Orders- Requirements Mounting: Flange type stainless steel Contact us for special requirements Wiring Hub: 1/2 inch threaded Toll Free: 1-800-369-6671 Minimum Operating Temp: -30 C Maximum Case Temp: 90 C E-mail:[email protected]