Larson Electronics 6000W Generator - Water Cooled Diesel Engine - 14' to 30' Fold-over Tower - (4) 400W LED Fixtures

The WCDE-4-30FT-4X150LTL-LED mobile light tower from Larson Electronics is a towable, self-contained LED light plant powered by a water cooled diesel engine turning a single bearing 4 pole generator which produces 6,000 watts at 120/240V @ 60Hz. The four 400 watt LED lamps included with this unit produce a combined total of 240,000 lumens, which can illuminate a 3-4 acre area. This 640 watt LED lighting package is a direct replacement for metal halide light plants. The telescoping, three-stage mast is capable of reaching heights up to 30 feet and retracting to 14 feet. The WCDE-4-30FT-4X150LTL-LED mobile light tower is a self-contained towable light tower package that produces enough light to illuminate an area up to 4 acres in size. This unit contains a water cooled diesel engine powering a 6,000 watt generator, which supplies the current to four 400 watt LED lamps producing 60,000 lumens each for a combined total of 240,000 lumens of light. This unit can run uninterrupted for 120 hours straight without refueling and includes a telescoping light mast which can elevate the four LED lamps to a height of 30 feet (and lowered to 14 feet). This mobile floodlight package is ideal for emergency services, large scale event illumination, construction, mining, industrial operations and anywhere an extended operation capable mobile lighting solution is needed. The three-stage, fold-over tower is constructed of square steel tubing with a lower section 12` in length and 4" by 4" by 1/8" thick, middle section 11` in length and 3" by 3" by 1/8" thick, and an upper section 10` and 2" by 2" by 1/8" thick. Each section has a 1` overlap. The mast is elevated using an included 1,000 lb hand winch with 3/16" cable and extended to its full height using a second 1,000 lb hand winch. The WCDE-4-30FT-4X150LTL-LED mobile light tower incorporates a long list of impressive features. The diesel engine is a water cooled Kubota that operates at 1800 rpm. This engine features key operated electric starting, a full twelve volt electrical system, automatic low oil pressure and high temperature safety shutoffs, dual fuel filters and easy access oil and radiator drain ports to facilitate maintenance. A 30 gallon fuel tank allows the engine to operate for 120+ hours continuously without refueling. The 6,000 watt generator is a single bearing design and produces 120/240 volt current at 60 Hz. The generator uses a four wire hookup system with an external ground allowing for setting up both electrical and mechanical safe grounding systems. Lights: The lighting system on this unit is comprised of four 400 watt LED lamps producing 60,000 lumens of light each attached to the end of the telescoping light boom. These floodlights produce a wide flood light pattern capable of illuminating 4 acres with a combined total of 240,000 lumens of light. Each floodlight is securely fastened to the light boom and each lamp includes a support bracket to help maintain lamp stability within its housing. The lamps are connected to the power source via a water tight male pin connector that attaches to a receptacle located on the end of the telescoping boom. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units feature individual heat sinks per bank of six LEDs to control heat buildup rather than utilizing a single housing to dissipate heat. This allows for more thorough cooling of the LEDs for extended operating periods. This allows the LEDs to be driven at up to 90% capacity without overheating or visible loss of light output. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 80,000 hours. In addition, should an LED failure occur, these LED flood lights are field serviceable. Each bank of six LEDs can be replaced with the fixture installed. This allows for the tower to stay in operation until repairs can take place, and eliminates the need to remove and disassemble the entire fixture for repairs. Durability: As well as unparalleled heat control, the GAU-LTL series of LED lights from Larson Electronics also offer IP67 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40¡ Celsius to +80¡ Celsius, are waterproof, and resist ingress of dust, dirt and humidity. The housings are formed from die cast aluminum and the optics are high transmission PMMA with 98% light transmittance. The Cree¨ LEDs help these units achieve resistance to vibrations and are rated at 70% lumen maintenance after 80,000 hours of use. We use these LED lights for applications where a lot of vibration, dust, dirt, dampness and abusive working conditions are encountered. LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life. LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases, vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps. Controls: The operations system for this unit is a centrally located control panel within the light tower enclosure. Four circuit breaker protected switches allow individual control of the lights while an individual hour meter tracks unit operating time. Also included is an alternator warning light, fuel primer system, preheating switch, 120 volt GFCI duplex receptacle for auxiliary power takeoff and a 240V twist lock power receptacle. Telescoping Boom: The mast is powder coated with a glossy blue finish for corrosion resistances and aesthetics. The LM family of telescoping towers feature a proprietary mast guidance system, which provides increased stability during high winds. When lowered to 14`, the mast can withstand winds up to 125 mph. When elevated to its full upright position, the mast can be rotated a full 360¡. By loosening the T-Handle, operators can rotate the mast with ease in either direction. The mast can be positioned in one of four different directions, and locked back in place by re-tightening the T-handle. The mast itself spins freely, and can typically be rotated with a single hand. The stabilizing outriggers are a three point design with one located under the trailer tongue and two on the rear sides of the unit. The two rear outriggers are adjustable and include 1,000 lbs. swivel jacks for leveling and stabilizing the tower. Housing: All of the operating components are housed within a protective compartment constructed of recyclable LMDPE (linear medium density polyethalene) plastic. This material is extremely corrosion resistant and retains its original appearance even after years of use. The enclosure is high impact crack resistant and retains resale value for longer than metal counterparts while also minimizing environmental impact. The highly durable plastic material is fully UV stabilized, contains long term antioxidants and is resistant to both high and low temperatures. The plastic enclosure of the WCDE-4-30FT-4X150LTL-LED is significantly lighter than comparable metal enclosures while offering a more attractive appearance. A vertical lift door provides access to the interior while latches provide secure closing while the unit is in use. The entire unit can be loaded and unloaded onto trucks via forklift sleeves mounted to the outer section of the light mast. The entire unit is mounted onto a two wheel trailer with a 2,000 lbs. leaf spring axle. A standard two inch ball coupling, three inch pintle hitch and two standard safety chains allow for easy hookup and towing. At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or message [email protected] for more information about our custom options tailored to meet your specific industry needs. Specifications / Additional Information WCDE-4-30FT-4X150LTL-LED Mobile LED Light Plant Ratings Genset Specs: 6KW Kubota Brushless Genset Engine: Kubota D1105-BG-ET01 30 Gallon Fuel Cell Engine Type: Vertical, liquid-cooled, 4-cycle diesel engine Up to 120+ Hour Continuous Operation Engine Speed: 1800 RPM External Grounding No. of Cylinders: 3 Low Oil, High Engine Temp Auto Shut-Off Generator: Marathon Pancake 6KW 4-Pole Brushless Hour Meter - Alternator Warning Voltage: 120/240V Single Phase High Output LED Lamps Auxiliary Power Supplies: 120V Duplex Receptacle, 240V Twist Lock Extreme Area Coverage Battery: 12V Direct Replacement for (4) 1000W MH Light Plants Fuel Cell Capacity: 30 Gallons 640W LED compared to Higher Wattage MH Fuel Delivery: Electric 240,000 Total Lumen Output Noise Level: Db level 63 @ 23 ft. Independently Adjustable Light Heads Individual Light Switch Circuit Breakers Light Mast Specs: Dial-in Adjustability per light head Mast Type: Telescoping, Fold Over 98% Transmission High Purity PMMA Optics Boom Height: 14` to 30` Multiple LED Banks for Heat Dispersion Materials: Steel - Powder Coated Gloss Blue 150 Lumens Per Watt Efficiency Operation: (2) 1,000lbs Manual Winches, Electric Optional 70% Lumen Retention after 80,000 Hours Cable: 3/16" Aircraft Cable IP67 Waterproof LED Fixtures Stages: Three Steel Trailer w/ Industrial Grade Paint Finish Three Point Outrigger System LED Light Specs: Withstands 125Mph Winds (Lowered) Lamp Type: Cree¨ LED Total Watts: 640 (400W per lamp) Total Lumens: 240,000 (60,000 per lamp) Luminous Efficiency: 135 Lm/W LED Color Temperature: Cool White - 5500-6500K LED Life Expectancy: 80,000 hours Optics Efficiency: 98% - PMMA High Transmittance Optics Led Drive %: 90% Power Factor: >97% Mounting: Stainless Steel Trunnion Mount U-Bracket Materials: Die Cast Aluminum Housing, Acrylic Optics Housing Color: Natural Aluminum Ambient Temperature Range: -40¡C to +80¡C Waterproof Rating: IP67 Coverage: 3 to 4 Acres Trailer Specs Materials: Plastic Enclosure, 12ga Formed Steel Chassis Hitch: 2" Ball Coupler and 3" Pintle Hitch Finish: Industrial Grade Paint Axle: (1) 2,000 lbs. Special Orders- Requirements Suspension: 2,000 lbs. Double Eye Leaf Springs Contact us for special requirements Outriggers: (4) Adjustable Outriggers w/ 2,500 lbs. Manual Leveling Jacks Toll Free: 1-800-369-6671 Lighting: DOT Approved tail, side, brake, and directional lights Intl: +01-903-498-3364 Wheels: (2) 13" 5x4.5 Steel Rims Fax: 1-903-498-3364 Tires: ST175/80/D13 E-mail: [email protected] Scroll Down to Purchase