Lotus LED Lights LB4R 4_ Round Super Thin Economy 11W LB4R

Discover Our Economy Ð Builder Grade super Thin LED recessed fixture

CONSTRUCTION:
Round 4_ fixtures with integral LEDs. Class 2 Isolated external driver factory installed inside junction box.
One driver for every fixture required.

MOUNTING:
Cut out hole in ceiling (4 1/4_ to 4 1/2_) and snap fixture in opening with attached spring clips.
Space in ceiling needed for the driver to fit through the hole Ð 2_.

• Default Driver Input Voltage: 120V Triac Dimmable
• Optional Driver Input Voltage: 120-347V 0-10V Dimmable
• Power factor: > 0.98
• Energy Used: 11W
• Halogen equivalent: 65W
• Beam Angle: 110¡
• Light colour options: Warm White 3000K, Neutral White 4100K, Dim to Warm 3000K to 2000K
• Light output: Warm White 700 lm, Neutral White 730 lm, Dim to Warm 700 lm
• CRI: > 80
• Ambient Operating Temperature: -40¡F (-40¡C) to +104¡F (+40¡C)
• Compliance: cULus Listed, certified to CSA STD. C22.2 No. 250.0
• Rated: Type IC (Direct Contact with Insulation), Energy Star (30K and 41K only), Air-Tight

DIMENSIONS:

• ID 4_; OD 4 7/8_; Thickness 1/2_
• Cut out: 4_ to 4 1/4_
• Junction Box Dimensions (with driver inside): 3 3/4_ x 3 3/8_ x 1 1/2_

Suitable for damp locations and soffit installations.

ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.

Recessed LED Lights Driver Installation:

CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove one of the half-inch knockouts on the side plate. Install standard L16 cable connector. Use double connector for daisy chaining multiple drivers. Insert line voltage feed into the cable connector and splice same colour wires using wire nuts. Close the cover. Connect the driver to the light fixture Ð the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand. Do not attach the junction box to anything so you can pull it through the ceiling opening in case you need to service the driver in future.

OPTIONS FOR LOCATING DRIVER:

Fixture comes connected to the driver by 12_ long low voltage cable with waterproof connector in the middle.
Depending on where you want the driver to be you have 2 options:

1. Locate next to the fixture Ð run line voltage wiring to first junction box and Òdaisy chainÓ to the junction boxes of the other fixtures.
2. Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 10 feet (3m) Ð cat # EXC10. Cables are linkable.
   Maximum run should not exceed 40 feet (12m).

DIMMING:

We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.

LIST OF COMPATIBLE DIMMERS

WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE LOTUS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER Ð NO SERVICEABLE PARTS INSIDE.

White Ð WH

Black Ð BK

Specification Sheet
Spec Sheet LB4R

pdf files
LB4R/30K | LB4R/41K | LB4R/32K dim to warm

IES files
LB4R/30K | LB4R/41K| LB4R/32K dim to warm

Links to Energy Star: LB4R/30K | LB4R/41K