Larson Electronics Infrared LED Light Emitter - 36 Watts - 12 IR Emitters LED's - 9-42VDC - 750/850/940NM

Buy American Compliant The Larson Electronics LEDLB-12-IR LED Light Bar offers high infrared light output in a light weight, durable, low profile housing combined with versatile mounting and power options. This IP67 rated infrared LED light bar is waterproof to one meter and produces 3,600mW of infrared light while drawing only 36 watts of power at 3 amps from a 12 volt electrical system. This light can run on any voltage from 9 to 42 Volts DC and produces an infrared light beam that can only be seen through the use of night vision goggles. We also offer other wavelength options tha include 750Nm, 850Nm or 940Nm. Click here to see the LED version of this The LEDLB-12-IR LED light bar from Larson Electronics produces a 550` long by 70` wide infrared light beam with 3,600mW of light in the infrared spectrum while drawing only 36 watts @3 amps from a 12 volt electrical system. Twelve Edixeon¨ thee watt Infrared Emitters LED`s producing 300mW each are paired with high purity 10¡ degree optics to produce a tightly focused spot beam with limited spread or light spillage. We also offer optional floodlight versions with 35¡ degree optics to produce a wider infrared beam spread. We offer 750Nm, 850Nm versions that are ideal for most IR applications and 940Nm versions that require the latest IR equipment for full effectiveness. These LED light bars are IP67 rated and waterproof to one meter, sealed against intrusion by dust and dirt and ruggedly constructed to withstand demanding environments and applications. The entire Larson Electronics LEDLB series are constructed of extruded aluminum and feature rubber isolated mounts and unbreakable polycarbonate lenses to provide durability and resistance to vibrations, impacts, waves, hard rains, sand and high winds. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. As a result, many manufacturers reduce the output of their LEDs to reduce the amount of heat produced. These LED light bars utilize an extruded aluminum housing that incorporates an advanced heat radiating fin design which dissipates heat efficiently to produce the maximum amount of power and longevity from the integrated Edison Edixeon¨ Emitters. The end result is more light and longer LED life of 50,000 hours. Voltage Control: These units are able to monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels ranging from 9 to 42 VDC. These LEDLB series light bars can operate on current ranging from 9 to 42 VDC without any modifications necessary as a result. This multi-voltage capability makes these units ideal for mobile and stand alone applications such as those found on boats, heavy equipment and vehicles where power systems don’t always operate with 12 volts and external generators, transformers or inverters are impractical. LEDLB-12-IR 35¡ Flood Beam(Opt) LEDLB-12-IR 10¡ Spot Beam(Stnd) Durability: The LEDLB series of LED light bars from Larson Electronics offer IP67 rated construction that is designed to withstand tough environmental and operating conditions. These units can operate in temperatures ranging from -40 degrees Celsius to 85 degrees Celsius, are waterproof to one meter and resist ingress of dust, dirt and humidity. The housings are formed from extruded aluminum, the hardware is stainless steel and the lenses are unbreakable polycarbonate. The Edixeon¨ LEDs offer inherent LED resistance to shocks and vibrations, contributing to these units 15.6Grms rating of vibration tolerance. These LEDLB series light bars are ideal for use in marine environments as well as industrial and commercial settings. Mounting: These LEDLB light bars feature a smaller profile and lighter weight than our LEDLB-E extreme series lights, making them ideal for use in locations where traditional lights cannot fit or would block other mounted equipment. Larson Electronics LEDLB series light bars are equipped standard with aluminum mounting blocks which slide within the aluminum housing to allow users to adjust their positioning to match existing or user drilled mounting holes. Each aluminum mounting block has an integrated rubber bushing to absorb vibrations and shocks. To secure the lights in place users simply slide the mounting bolts through the aluminum mounting block and rubber isolator, through the mounting surface, then secure the bolt with a locking nut on the opposite side of the mounting surface. We also offer a BC-2 bar clamp mounting system you can view here for even greater mounting versatility. Note: Most Larson Electronics LEDLB, LEDLB-E, LEDP3W, LEDP10W, and LED10W series LED spotlights and floodlights are terminated with a Deutsch IPD / LADD DT04-2P connector. The mating connector plug is DT06-2S. Most LEDLB and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. high/low beam, modulating, IR/Visible combos) will have different Deutsch connectors. Specifications / Additional Information LEDLB-12-IR Infrared LED Light Bar LEDLB LED Features LEDs: 12 Edixeon¨ 3 Watt Infrared LED Emitters Edixeon¨ 3 Watt LED Emitters Dimensions: 8"-L 5"-H 3.00"-D LEDs Driven At 80% Watts: 36 -40 C~ +80C Operating Temp Range Voltage: 9-42 VDC IP67 Rated Waterproof to 3 meter Spot Beam:550`L x 70`W CE Certified Flood Beam: 120`L x 100`W EN55015 EMI Weight: 3.3 Lbs EN61547 EMS Lighting Configuration: 10¡ Spot or 35¡ Flood EN62471 Photobiological Safety Mounting: Stud Bracket Wiring: Deutsch IPD / LADD DT04-2P connector Amps: 3 (on 12 volts) 1.5 (on 24 volts) Megawatts: 3,600 Wavelength: 750Nm, 850Nm or 940Nm Infrared Special Orders- Requirements LED Life Expectancy: 50,000 hours Contact us for special requirements Optics Efficiency: 90% Toll Free: 888-325-4448 Materials: Aluminum Housing, Polycarbonate Lens Housing Colors: Black or White. E-mail: [email protected] Down to Purchase-