Larson Electronics Explosion Proof Fluorescent Lights w/ Emergency Battery Backup - 2 foot 4 Lamp - Multi-Volatge

Made in the USAThe Larson Electronics EPL-EMG-24-4L-T5HO Explosion Proof Fluorescent Light Fixture with Emergency Battery Backup is NRTL Listed for United States and Canada Class 1 Division 1, Class 2 Division 1 and ideal for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist.***PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO THIS HAZARDOUS LOCATION LIGHT FIXTURE***The EPL-EMG-24-4L-T5HO fixture is a 2 foot long, 4 lamp, Class 1 Division 1 and Class 2 Division 1 & 2 explosion proof emergency fluorescent light equipped with emergency backup battery operation. This T6 temperature rated fixture comes standard with F24-T5/HO lamps and an emergency backup ballst for failsafe illumination during power outages. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture is multi-voltage capable and for use in paint spray booths.The EPL-24-4L provides operators in hazardous locations with a compact, reliable and affordable lighting solution that provides the best explosion proof protection available without sacrificing light quality or fixture durability. This fluorescent light works, mounts and is wired like our EPL-24-4L explosion proof fluorescent light fixtures. The main difference is that we attach an extra Bodine Ballast Box to the unit that adds emergency light functionality to the fixture. This explosion proof emergency light will run the standard 90 minutes after power is lost. The light recharges the battery once electrical power is restored. Standard configuration includes a single emergency ballast that will run a single lamp at 1350 lumens for 90 minutes. For an additional charge, a second ballast can be added to run a second lamp for 2700 total lumens output for 90 minutes. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.NOTE ON LAMPS: We offer a choice of bulbs with all of our explosion proof fluorescent fixtures. We standardize on the T5HO bulbs mostly for their longevity and high output. However, many of our customers, including Naval bases, shipyards, oil rigs and petrochemical processing plants operate in very cold conditions and T12HO bulbs operate well in those environments. The T12VHO, 110 watt Very High Output lamps make this fixture an ideal replacement for 400 watt metal halide surface mount fixtures in hazardous location areas requiring Class 1 Division 1 rated lights. Please inquire about additional lamp options.Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit).Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fluorescent light. Made in USA QualityLamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.F24-T5HO – 2000 lumens per bulb (4000 lumens total), 20,000 hours life, 5000 Kelvin color, CRI 85 RHA-UNV-254-LT5 Ballast is THD<10% and HPF .98Specifications / Additional Information EPL-EMG-24-4L-T5HO Explosion Proof RatingsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and DLamp Type: Fluorescent Class 1 Division 2, Group A,B,C,DDimensions: W-22.50" L-27" H-8.5 " Class II Division 1- 2, Groups E,F,GWeight: 57 Lbs NRTL Certified to UL 844, 924Voltage: Multi- 120V-60hz 220V-50hz 240V-60hz 277V-60hz NRTL Certified to UL 1598 Marine TypeTotal Watts: 96 Watts NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Total Lumens: 8,000 Listed for Paint Spray Booths*Luminous Efficacy: 83 Lm/W California Title 24 CompliantLamp Life Expectancy: 20,000+ Hours Switch Leg for Powering Light On/OffColor Temp: 5000K Beam Angle: N/A Ambient Operating Temp Range: -30¡ C to 70¡ C Operating Temp Rating: T6 Rated Minimum Operating Temp: -30¡ C Maximum Case Temp: 90¡ C Mounting: Bracket Standard - Pendant Optional Wiring Hub: 1/2 inch threaded Special Orders- Requirements?Contact us for special requirementsToll Free: 888-325-4448Intl: 1-903-270-1187E-mail: [email protected]