Larson Electronics Explosion Proof Fluorescent Lights - Paint Booths, Rigs - 4', 8 Lamp Fixture - Bi-Axial Bulb Design

Made in the USAThe Larson Electronics EPL-48-4L-BX Explosion Proof Eight Bi-Axial Bulb Fluorescent Light Fixture is NRTL Listed for United State and Canada Class 1 Division 1, Class 1 Division 2, carries a T6 temperature rating and ideal for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist.***PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO THIS HAZARDOUS LOCATION LIGHT FIXTURE***The EPL-48-4L-BX fixture is a 4 foot long, 8 lamp, Class 1 Division 1 and Class 2 Division 1 & 2 explosion proof fluorescent light which is also approved for use in paint spray booth applications. This T6 temperature rated fixture comes standard with eight Bi-Axial 40 watt compact fluorescent bulbs which produce a combined 320 watts of illumination. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. The EPL-48-4L-BX provides operators in hazardous locations with an effective explosion proof lighting solution that provides more light than similar two bulb units.Connector pins closeupConnector pins closeupConnector pins closeupClick Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeThis Biaxial Lamp fixture is multi-voltage capable and can operate on voltages ranging through 100/120 Volts 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ, and 277 Volts 60 HZ with 347 Volt and 480 Volt versions available upon request.Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit).Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fluorescent light.Made in USA Quality1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Larger ballast box accommodates High Output lamp ballasts. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Specifications / Additional Information EPL-48-4L-BX RatingsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and DLamp Type: Fluorescent Class 1 Division 2, Group A,B,C,DDimensions: W-11.25" L-52" H-8.5 " NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Weight: 65 Lbs NRTL Certified to UL 844, 924Voltage:120V-60hz 220V-50hz 240V-60hz 277V-60hz NRTL Certified to UL 1598 Marine TypeOptional Voltages: 347 Volt and 480 Volt Class II Division 1- 2, Groups E,F,GTotal Watts: 320 watts Certified to Canadian StandardsTotal Lumens 28,000 Listed for Paint Spray BoothsLuminous Efficacy: 88 Lm/W California Title 24 CompliantLED Lamp Life Expectancy: 20,000+ Hours Color Temp: 4000K Beam Angle: 150¡ Ambient Operating Temp Range:-30¡C to +70¡C Operating Temp Range: T6 rated Special Orders- RequirementsMounting: Bracket Standard - Pendant Optional Contact us for special requirementsWiring Hub: 1/2 Inch Threaded Toll Free: 888-325-4448Intl: 1-903-270-1187E-mail: [email protected]