Larson Electronics Explosion Proof Fluorescent Light - 2 foot - 2 lamp - Emergency Backup Ballast - T8 -Multi-voltage

Made in the USAThe Larson Electronics EPL-EMG-24-2L-T8 Explosion Proof Fluorescent Light Fixture is NRTL Listed for United States and Canada Class 1 Division 1, Class II Division 1 and ideal for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist.The EPL-EMG-24-2L-T8 fixture is a 2 foot long, 2 lamp, Class 1 Division 1 and Class II Division 1 & 2 explosion proof fluorescent light and an ideal choice for use in applications where space is at a premium. This T6 temperature rated fixture comes standard with F17-T8/HO lamps and is available with a variety of lamp options which are listed below. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture is multi-voltage capable and for use in paint spray booths. The EPL-EMG-24-2L-T8 provides operators in hazardous locations with a compact, reliable and affordable lighting solution that provides the best explosion proof protection available without sacrificing light quality or fixture durability. This fluorescent light works, mounts and is wired like our EPL-EMG-24-2L-T8 explosion proof fluorescent light fixtures. The main difference is that we attach an extra Bodine ballast box to the unit that adds emergency light functionality to the fixture. This explosion proof emergency light will run the standard 90 minutes after power is lost. The light recharges the battery once electrical power is restored. Standard configuration includes a single emergency ballast that will run a single lamp at 1350 lumens for 90 minutes. For an additional charge, a second ballast can be added to run a second lamp for 1800 total lumens output for 90 minutes. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode. NOTE ON LAMPS: This unit comes equipped with an electronic ballast and F17-T8/HO bulbs which produce 2650 lumens per bulb and have a rated lifespan of 24,000 hours. Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fluorescent light. Made in USA Quality Lamp Options 1. Each unit dielectrically tested. 2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection. F17-T8/HO – 1325 lumens per bulb (2650 lumens total), 24,000 hours life, 4100 Kelvin color Specifications / Additional Information EPL-EMG-24-2L-T8 Explosion Proof RatingsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and DLamp Type: Fluorescent Class 1 Division 2, Group A,B,C,DDimensions: W-11.25" L-27.5" H-8.5 " Class II Division 1- 2, Groups E,F,GWeight: 55 Lbs NRTL Certified to UL 844, 924Voltage: Multi- 120V-60hz 220V-50hz 240V-60hz 277V-60hz NRTL Certified to UL 1598 Marine TypeTotal Watts: 48 watts* NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Total Lumens: 2,650 Listed for Paint Spray Booths*Luminous Efficacy: 55 Lm/W California Title 24 CompliantLamp Life Expectancy: 24,000 Hours Switch Leg for Powering Light On/OffColor Temp: 4100K Beam Angle: N/A Operating Temp Range: T6 Rated Mounting: Bracket Standard - Pendant Optional Wiring Hub: 1/2 inch threaded Special Orders- Requirements*Wattage totals are lamps only and may vary with different lamps. Contact us for special requirementsToll Free: 888-325-4448Intl: 1-903-270-1187E-mail: [email protected]