Larson Electronics Explosion Proof Emergency Lights & Fluorescent light Combination - 2 foot - 2 lamps

Made in the USAThe Larson Electronics EPL-EMG-24-2L Explosion Proof Paint Booth Fluorescent Emergency Light Fixture is NRTL Listed for United States and Canada Class 1 Division 1, Class 2 Division 1 and ideal for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist. The standard model includes an emergency ballast and T8 lamps.Click here to see the LED version of this lightThe EPL-EMG-24-2L is a 4 foot long, 2 lamp, Class 1 Division 1 and Class 2 Division 1 and 2 explosion proof fluorescent light which is equipped with an added battery backup providing 90 minutes of emergency runtime. This fixture comes standard with two T-8 fluorescent lamps which produce a combined 2,700 lumens of light. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture is multi-voltage capable and provides operators in hazardous locations with a reliable and durable lighting solution that provides explosion proof protection along with the security of an emergency battery backup. This fluorescent light works, mounts and is wired like our EPL-24-2L explosion proof fluorescent light fixtures. The main difference is that we attach an extra Bodine ballast box to the unit that adds emergency light functionality to the fixture. This explosion proof emergency light will run the standard 90 minutes after power is lost. The light recharges the battery once electrical power is restored. Standard configuration includes a single emergency ballast that will run a single lamp at 1350 lumens for 90 minutes. For an additional charge, a second ballast can be added to run a second lamp for2700 total lumens output for 90 minutes. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode. Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the opposite end of the fluorescent light. Made in USA Quality Lamp Options 1. Each unit dielectrically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Over-sized, finned ballast housing for 800 mA fixtures provides more heat dissipation and extends ballast life. Ballast housing easily accessible and externally mounted. Top and bottom covers secured with nuts and bolts, instead of threaded through holes, which can be damaged with dirt.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. A wrench is used to unscrew the end caps for relamping the fixture, while other models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection. F17-T8 – 1325 lumens per bulb (2650 lumens total), 24,000 hours life, 4100 Kelvin color Specifications / Additional Information EPL-48-2L Explosion Proof RatingsNRTL Listed for United States & Canada Class 1 Division 1, Groups C and DDimensions: W-11.25" L-29 " H-8.5 " Class 1 Division 2, Group A,B,C,DWeight: 65 Lbs Class II Division 1- 2, Groups E,F,GTotal Watts: N/A* NRTL Certified to UL 844, 924Voltage: Multi- 120V-60hz 220V-50hz 240V-60hz 277V-60hz NRTL Certified to UL 1598 Marine TypeTotal Lumens: F17-T8 Bulbs 2650 NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Lamp Life Expectancy: F17-T8 Bulbs 24,000 Hours Listed for Paint Spray Booths*Efficiency: N/A Switch Leg for Powering Light On/OffOperating Temp Range: T6 Rated -30 C to 70 C Beam Angle: N/A Color Temp: 4100K- Special Orders- RequirementsMounting: Bracket Standard - Pendant Optional Contact us for special requirementsWiring Hub: 1/2 inch threaded Toll Free: 888-325-4448Intl: 1-903-270-1187*Wattage totals are lamps only and may vary with different lamps. E-mail: [email protected]?