Larson Electronics Explosion Proof C1D2 0-10V Dimmable LED Fixture - 2ft 2 Lamp - Emergency Ballast - Terminal Strips

Made in the USAThe Larson Electronics HAL-EMG-24-2L-LED-D-V2 Hazardous Area Dimmable LED Light Fixture is NRTL Listed for United States and Canada Class 1 Division 2 Groups A, B, C and D - NRTL Certified to UL 1598A listed, has a T4C temperature rating and ideal for open air hazardous locations where flammable chemical/petrochemical vapors may be occasionally encountered. This dimmable C1D2 light fixture is compatible with 0-10V dimmer switches, and contains internal terminal strips for wiring multiple fixtures in series.The HAL-EMG-24-2L-LED-D-V2 fixture is a 2 foot long, 2 lamp, Class I Division 2 Groups A, B, C and D hazardous area dimmable LED light that takes the reliability and efficiency of a fluorescent fixture and adds even longer lamp life and efficiency with high output LEDs. This fixture is T4C temperature rated and comes standard with our high power 14 watt dimmable LED lamps that each produce 1,750 lumens. The lamps are protected by an aluminum framed hinged glass door secured with two turn latches and the fixture is constructed of copper free aluminum alloy. The lamp reflector is corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. A factory installed terminal strip within the light fixture allows operators to wire multiple fixtures in series, reducing installation cost. The internal terminal strip accounts for dimming control wires (violet/grey) for dimming multiple fixtures in series from a single switch.This fixture can be configured to run on voltages from 90-132V AC and is NRTL Certified to U.L. 595 and UL 1598A Marine Type approved for use marine environments. The HAL-EMG-24-2L-LED-D-V2 is weatherproof and provides operators in hazardous locations with a highly efficient, reliable and affordable lighting solution for open areas where flammable chemicals and vapors my occasionally be present.This LED light fixture features 0-10V dimming capabilities. This gives operators the ability to manually adjust the brightness of the LED lamp quickly and easily. The 0-10V dimming allows for adjustments to fit the brightness needs of any lighting situation. A 0-10V dimmable light works through the use of a DC control signal that ranges between zero and ten volts. The basic idea is that at 10 volts of input the light is at its brightest level with 0 volts being the lowest possible dimness setting. The smooth, continuous and flicker-free dimming of a 0-10V dimmable LED light is ideal for a wide range of different lighting applications.This dimmable LED light works operates as a standard light fixture during normal operation while line voltage is present. The main difference is that we add a battery backup unit that adds emergency light functionality to the fixture. This hazardous area emergency light will run one bulb at the standard suggested 90+ minutes after power is lost. The light recharges the battery once electrical power is restored. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode. Emergency mode will operate regardless of if the fixture is turned on or off. A test switch can be installed for routine testing.Click Photo to EnlargeClick Photo to EnlargeClick Photo to EnlargeSurface Mount (Standard)Pendant Mount (Optional)We have eliminated the ballast normally associated with fluorescent fixtures which reduces overall weight, increases lamp life to an extreme 50,000 hours and helps this LED fixture maintain a T-4C temperature rating. The solid state design of the included LED lamps give this fixture superior resistance to damage from vibrations and extremes in temperature as well as a lamp service life over twice that of standard T5-bulbs. The 14 watt LED lamps produce more illumination than standard T5 bulbs, but draw only 1/2th of the current. The current generation of Larson Electronics LED T-series style bulbs produce 15% more light than standard T5 bulbs.Standard Surface Mount Brackets: Each L bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. Mounting brackets are removable. A single through hole enables the operator to install the light to any surface.A sliding bracket mount is available so operators can retrofit this LED light fixture to use the pre-existing mounting holes from other fluorescent fixtures. Contact us for the sliding bracket option.Suggested Applications:Aircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Chemical manufacturing, Waste treatment plants, Gas processing plants.At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or [email protected] for more information about our custom options tailored to meet your specific industry needs.Made in USA Quality Superior LED Benefits1. Each unit dielectrically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Adjustable mounting brackets enable the operator to choose any mounting angle for the fixture, where other models may only offer one or three choices.3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy.4. Relamping done via 4 turn latches, which enable the operator to unlatch the hinged door and access the lamps.5. Heavy gauge extruded aluminum reflectors with high gloss reflective finish. Resists dents and corrosion.6. 1/2" or 3/4", threaded access hole for wiring conduit. 7. Units can be wired end to end in series. Internal terminal strip allows operators to terminate wires within fixtures.1. 50,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces energy use and prolongs life-spans of peripheral cooling units (A/C, refrigeration)5. 100% recyclable.6. No toxins-lead, mercury.7. No UV light, infrared radiation or CO2 emissions.8. Qualifies buildings for LEED and other sustainable business certifications.9. Bright, even light maintains consistent color over time.10. Instant on/off - No flickering, delays or buzzing. 11. Very good color rendering.12. Vibration/impact resistant.13. Significantly cooler operation.14. Less frequent outages, higher output improves workplace safety.Specifications / Additional InformationHAL-EMG-24-2L-LED-D-V2 Hazardous Area RatingsNRTL Listed for United States & Canada Class 1 Division 2, Groups A, B, C and DLamp Type: Dimmable LED NRTL Certified to UL 595 Outdoor Marine Type (Saltwater)Dimensions: 27.9"L x 7.12"W x 9.11"H - Surface Mount NRTL Certified to UL 1598A Marine TypeWeight: 17 Lbs Switch Leg for Powering Light On/OffVoltage: 90-132V AC, 50/60Hz 0-10V DummableDimming: Yes - 0-10V Dimmable Total Watts: 28 watts Total Lumens: 3,500 Luminous Efficacy: 125 Lm/W LED Lamp Life Expectancy: 50,000 Hours Power Efficiency: 90% Power Factor: >0.95 Color Temp: 4500K or 5600K Beam Angle: 150¡ Ambient Operating Temp Range:-25¡C to +45¡C Operating Temp Range: T4C rated Mounting: Bracket Standard, Sliding Bracket Optional Special Orders- RequirementsWiring Hub: 1/2" or 3/4" threaded Contact us for special requirementsBattery Backup: 90+ minute runtime Toll Free: 888-325-4448Warranty: YES-3 Years* Intl: 1-903-270-1187? E-mail: [email protected]