Larson Electronics Class I, Div. II LED Fixture - 4ft. 2 Lamps - Corrosion Resistant - 220Volts, 50/60Hz - T-Style LEDs

Made in the USA The Larson Electronics HALP-48-2L-220V-LED Hazardous Area LED Light Fixture is U.S./Canada UL Listed Class 1 Division 2 Groups A, B, C and D - UL 1598A listed, has a T4A Temperature Rating and is specifically designed to handle the rigors of wet and corrosive marine environments. The HALP-48-2L-220V-LED hazardous area LED light fixture is designed for use in wet areas and saltwater-marine environments where corrosion resistance is critical to equipment longevity and safety. This Class 1 Division 2 rated fixture runs on 220Volt, 50/60Hz current and is constructed of non-corrosive materials including a polyester housing reinforced with glass fiber, a poured in gasket for reliable sealing and an impact resistant acrylic diffuser. Corrosion resistant plastic latches secure the lamp cover to the housing and provide a firm lock against the poured in seal to prevent drips and water intrusion. This fixture is UL 844 rated and Class 1 Division II, Groups A, B, C, D approved. The HALP-48-2L-220V-LED also carries a UL 1598A outdoor marine rating and meets US Coast Guard specifications. This lamp offers the extreme durability, high efficiency and long life of high power LEDs in a proven hazardous location fixture design. The HALP-48-2L-220V-LED is equipped with Larson Electronics’s specially designed LED T-series bulbs which produce 15% more foot candles of illumination at 8 feet as compared to standard T5 lamps when measured with an Extech light meter. The 24 watt LED lamps produce more illumination than standard T5 bulbs, but draw only 1/3rd of current. The HALP-48-2L-220V-LED works on 220Volt, 50/60Hz voltage. NOTE ON LAMPS: All hazardous location lights are shipped with bulbs. Two four foot 24 watt LED tube bulbs with a color temperature of 5300K and a 50,000 hour life span come equipped with this fixture . The HALP-48-2L-220V-LED is solid state and works with 220,50/60Hz current. Surface Mount (Standard) Standard Flange Brackets: Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide some shock absorbency protection while enabling the user to simply mount the fixture with the through-hole taps that protrude on each side of the fixture. The mounting holes are 36 9/16 inches on center apart along the top of this hazardous location light. The mounting holes are 7 inches on center across the top of the light. Pendant Mount (Optional) Suspension/Pendant Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture is equipped with either two 1/2" or 3/4” NPT hubs, one on each end of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to one of the NPT hubs and tied in to the fixture’s lead wires, completing the electrical connection. The remaining pendant hub provides support for the opposite end of the fixture. Suggested Applications:The HALP-48-2L-220V-LED is designed for marine, wet, damp locations where corrosion resistant LED lights are required. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas, water treatment areas, processing plants and marine loading docks. Made in USA Quality Superior LED Benefits 1. Each unit dialectrically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface. 3. Fixture housing constructed of glass fiber reinforced polyester. 4. No ballast box. No ballast to replace. We simply run the black wire to one end of the bulb and white wire to the other. 5. Relamping done via 6 plastic snap locking latches which enables the operator to remove the door and access the lamps. 6. Lamp cover-diffuser constructed of high impact acrylic for corrosion resistance and lamp protection. . 7. 1/2" or 3/4", threaded access hole for wiring conduit. 1. 50,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces energy use and prolongs life-spans of peripheral cooling units (A/C, refrigeration)5. 100% recyclable.6. No toxins-lead, mercury.7. No UV light, infrared radiation or CO2 emissions.8. Qualifies buildings for LEED and other sustainable business certifications.9. Bright, even light maintains consistent color over time.10. Instant on/off – No flickering, delays or buzzing. 11. Very good color rendering.12. Vibration/impact resistant.13. Significantly cooler operation.14. Less frequent outages, higher output improves workplace safety. Specifications / Additional Information HALP-48-2L-220V-LED Hazardous Area U.L. Ratings UL Listing: United States - Canada Class I Division 2, Groups A, B, C, D Dimensions: W-8.25 " L-52 " H-7" Class II, Division 2, Groups F, G Weight: 8 Lbs UL 844 Total Watts: 48 watts UL 1598A Marine Type (Salt water)California Title 24 Compliant Voltage: 220Volt, 50/60Hz Lamp Life Expectancy: LED T-Series 50,000 Hours Efficiency: LED T-Series 90 Lumens per Watt Operating Temp: T4A Rated -30 C to 70 CMinimum Operating Temp: -30 CMaximum Case Temp: 90 C Beam Angle: 150 degrees Color Temp: 5300K- Special Orders- Requirements Mounting: Flange type stainless steel Contact us for special requirements Wiring Hub: 1/2" or 3/4" threaded Toll Free: 1-800-369-6671 U.L Approval: U.S Certificate Canada Certificate E-mail:[email protected]