Larson Electronics Class I, Div. II Fluorescent Fixture - Emergency Battery Backup - Corrosion Resistant (Saltwater) -

Made in the USAThe Larson Electronics HALP-EMG-24-2L-BX Hazardous Area Fluorescent Emergency Light Fixture is U.S / Canada U.L approved Class 1 Division 2 Groups A, B, C and D - UL 1598A listed, has a T4A temperature rating and is specifically designed to handle the rigors of wet and corrosive marine environments. This fixture uses Bi-Axial design bulbs to increase wattage and light output without increasing fixture size or weight.The HALP-EMG-24-2L-BX hazardous area fluorescent emergency light fixture builds on the effectiveness of our HALP-24 series by including bi-axial lamps which raise the fixture`s wattage and light output totals without increasing the unit`s size or weight. Although some efficiency is sacrificed for increased output, this unit`s lower cost and increased ouput helps offset this lower efficiency. This Class 1 Division 2 rated fixture is constructed of non-corrosive materials including a polyester housing reinforced with glass fiber, a poured in gasket for reliable sealing and an impact resistant acrylic diffuser. Corrosion resistant plastic steel latches secure the lamp cover to the housing and provide a firm lock against the poured in seal to prevent drips and water intrusion. This fixture is UL 844 rated and Class 1 Division II, Groups A, B, C, D approved. The HALP-EMG-24-2L-BX also carries a UL 1598A outdoor marine rating and meets US Coast Guard specifications. This fixture ideal for hazardous areas where corrosion resistance is mandatory and space limitations require a powerful yet compact lighting solution.This fluorescent light works, mounts and is wired like our HALP-24-2L-BX explosion proof fluorescent light fixtures. The main difference is that we add a battery backup unit that adds emergency light functionality to the fixture. This hazardous area emergency light will run the standard UL suggested 90 minutes after power is lost. The light recharges the battery once electrical power is restored. Standard configuration includes a single emergency ballast that will run a single lamp at 900 lumens for 90 minutes. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode. NOTE ON LAMPS: This fixture comes equipped with Bi-Axial Bulbs which increases the wattage of the standard HALP-EMG-24-2L from 34 watts with 2 standard T5-HO lamps to 80 watts with bi-axial bulbs. The HALP-24-2L-BX has an electronic universal ballast and works on 120-277VAC.Surface Mounting: Flange type aluminum mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide some shock absorbency protection while enabling the user to simply mount the fixture with the through-hole taps that protrude on each side of the fixture. The mounting holes are 14.91" inches on center apart along the top of this hazardous location light. The mounting holes are 9.5" inches on center across the top of the light.Pendant Mounting:This light fixture can hang from the ceiling suspected by rigid pipe. Each fixture is equipped with either two 1/2" or 3/4" NPT hubs on either side of the fixture. Operators will bring rigid pipe down to the threaded mounting ups. The wiring is fed down through the rigid pipe to one of the NPT hubs and tied to the fixture`s lead wires to complete the electrical connection. The remaining pendant hub provides support for the opposite end of the fixture.Suggested Applications:The HALP-24-2L-BX is designed for marine wet and damp locations, where corrosion resistant fluorescent lights are required. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas, water treatment areas, processing plants and marine loading docks.Made in USA QualityLamp Options1. Each unit dialectically tested.2. Fixture arrives assembled and lamped to reduce installation time and cost. Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface.3. Fixture housing constructed of glass fiber reinforced polyester.4. Relamping done via stainless steel snap locking latches, which enable the operator to remove the door and access the lamps.5. Lamp cover-diffuser constructed of high impact acrylic for corrosion resistance and lamp protection.6. 1/2" or 3/4", threaded access hole for wiring conduit. Specifications / Additional Information HALP-EMG-24-2LU.L. RatingsUL Listing: United States - CanadaClass I Division 2, Groups A, B, C and D Lamp Type: Fluorescent Class II, Division 2, Groups F, G Dimensions: W-8.25 " L-26" H-7"UL 844Weight: 5 Lbs UL 924Voltage: Universal 120-277VAC 50/60 hzUL 1598A Marine TypeTotal Watts: 80 watts California Title 24 CompliantTotal Lumens T5-HO Bulbs: 5,300cUL Listed for CanadaLuminous Efficacy T5-HO Bulbs:: 66.25 Lm/WMeets USCG SpecsLED Lamp Life Expectancy: 20,000+ HoursT4 Temperature RatingColor Temp: 4100KSwitch Leg for Powering Light On/OffBeam Angle: 150¡Ambient Operating Temp Range:-40¡C to +65¡COperating Temp Range: T4A ratedMounting: Surface Standard - Pendant Optional Special Orders- Requirements Wiring Hub: (2) 1/2" or 3/4" threaded NPT hubs Contact us for special requirements Battery Backup: 90 minute runtime at 900 lumen Toll Free: 1-800-369-6671 U.L Approval: U.S Certificate Canada Certificate E-mail:[email protected]