Larson Electronics 30 KVA Power Substation - 480V to 208Y/120V - (12) 120V Receptacles - 18" Above Ground - 60' Cord

Made in Texas The Larson Electronics MPD-60C-480D-30KVA-208Y.120-12X120.20A-E18 power distribution substation converts 480V AC electrical current into three phase 208Y/120VAC. This unit provides operators the ability to safely tap into and distribute 480VAC power from a variety of sources including generators and direct grid power. Designed for aircraft hangar applications, all electrical components are mounted 18 inches above ground. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO POWER DISTRIBUTION PANELS, TRANSFORMERS, OR SUBSTATIONS* Portable Power Distribution Purpose and UseThe MPD-60C-480D-30KVA-208Y.120-12X120.20A-E18 portable power distribution system gives operators the ability to power their 120 volt equipment from a single system. On the primary side, operators connect 480V line-in power using a 60` 8/4 SOOW cord with a blunt-cut end. On the secondary side, twelve 120V duplex GFCI receptacles are available for 120V equipment. Operation: A 60` 8/4 SOOW cord with a blunt-cut end brings 480V three phase power to the NEMA 3R 60-amp, 480V three phase primary disconnect, which is fused at 40 amps, and passes power through to the transformer. The NEMA 3R 30 KVA transformer converts 480V to 208Y/120 three phase and passes the current to the secondary panel. The secondary side of the transformer feeds a NEMA 3R 125-amp, 208Y/120V three phase main breaker panel. This secondary panel contains twelve 20-amp breakers protecting twelve 20-amp, 120V duplex receptacles. Protective Construction: Unlike many portable power distribution boxes made of plastic and utilizing thin gauge, low grade metals in their construction, this unit is designed for serious use and is ruggedly constructed to withstand demanding conditions and heavy duty industrial applications. The transformer and load assembly is mounted on a 3/16" thick carbon steel mounting platform and the load center/distribution assembly is mounted to the standard 2" x 2" x 1/8" square carbon steel tubing frame, resulting in an extremely stable, durable and well protected power distribution platform. All electrical components are mounted 18 inches above ground. This model is equipped with forklift skid pockets, locking casters, and a top located lifting eyelet which allows easy lifting with cable or chain hooks. This can be replaced for an additional cost with stainless steel, hot dip galvanized steel, or aluminum depending on the customer’s needs. Larger units are available upon request and can be equipped with skids or trailer mounted. Certification: Larson Electronics is a UL 1640 panel shop and certified to build portable power distribution systems. All units are built in accordance to NFPA 70 (National Electric Code) and certified to UL 1640. All equipment is NEMA 3R rated for indoor and outdoor use and provide a degree of protection against dirt, water, and ice. NEMA 4 and NEMA 4x equipment can be equipped upon request. Grounding: Transformer is grounded to the frame and we provide a grounding lug on the frame for the earth ground. ~Please check all motor loads for dual rated motors that will work 208 or 240.~ Applications: This power distribution system is ideal for indoor or outdoor use and applications including but not limited to, construction sites, plant maintenance, plant turnarounds, shows, exhibits, and shipyard operations. These power distribution systems are popularly used in applications where external power sources are often necessary. We also offer class rated transformers for use within explosion proof and hazardous location environments. Custom Built Systems Available: Larson Electronics is a manufacturer and we can build portable power distribution systems to your specifications. Although we carry several models of portable power distribution systems in stock, we can deliver custom ordered units almost as quickly as our prebuilt units. If this model does not meet your needs, please contact us at 888-325-4448 [email protected] to discuss your specific requirements. Specifications / Additional Information MPD-60C-480D-30KVA-208Y.120-12X120.20A-E18 Power Transformer Line-In Cord: 60` 8/4 SOOW Cord w/ Blunt-cut End Max OCP Primary: 60A @ 480V Line-In Cord Cap: Customer Provided Max OCP Primary: 125A @ 208Y Primary Voltage: 480V 3PH UL 1640 Portable Power-Distribution Equipment Primary Disconnect: 60A 480V 3PH Fused @ 40A N3R NEMA 3R Indoor or Outdoor Use Primary Panel: - Made in the USA Primary Breakers: - 18" Above Ground Primary Receptacles: - Primary Protection: Disconnect Transformer: 30 KVA 480V to 208Y/120V 3PH N3R Secondary Voltage: 208Y/120V 3PH Secondary Panel: 208Y/120V 3PH 125A Main Breaker Panel N3R Secondary Breakers: (12) 20A Secondary Receptacles: (12) 20A GFCI Duplex [120V] Secondary Protection: GFCI Special Orders- Requirements Form Factor: Square tube frame w/ 1/8" side walls, hinged access doors, skid pockets, top pick eye & locking 8” locking casters Contact us for special requirements Frame Materials: Powder coated steel frame Toll Free: 888-325-4448 Dimensions: 48” X 48” X 62” Weight: 750 pounds E-mail: [email protected] Larson Electronics manufacture a wide variety of custom power distribution systems. The pictures displayed for this unit are a general representation of form factor and may not accurately represent this exact configuration in every detail due to being custom builds. The specifics for this configuration are listed in the specification table and one-line diagram. *All grounding shall comply with state and local codes and meet the minimum requirements of the National Electronic Code section 250* Scroll Down to Purchase