Larson Electronics 200 Watt 40" Dual Spot LED Light - 32 Cree LEDs - 17200 Lumens - Versatile Mounting Options

The LEDLB-40-CPR-2X25WRE from Larson Electronics is a 40” Dual Spot LED Light fixture which includes a 30.06” wide spot LED light bar and two LED spotlights, one attached to each end of the bar. This two-in-one spot LED fixture produces a total of 17,200 lumens of bright light, and provides operators with a versatile and powerful LED spot lighting solution for wide and narrow applications. Each LED component can be operated individually, or together. This dual spot LED unit is IP65 rated, ideal for outdoor locations. The LEDLB-40-CPR-2X25WRE LED Light is ideal for a wide variety of uses including indoor and outdoor locations where both general wide spot illumination and longer distance spot lighting is needed. The wide spot light bar is located at the center of this fixture and offers 150 watts of power producing an impressive 11,700 lumens from 30 super bright 5W CREE LED bulbs. The two LED spotlights are attached to the each of the light bar, and emit 2750 lumens of bright light from a single CREE 25 watt LED per unit, for a total of 5,500 lumens. These spotlights project a narrow 10¼ spot beam approximately 1000 feet long, but also offer a 60¼ flood beam configuration. The lamp heads are ultra compact at just 4.5" OD. The LEDLB-40-CPR-2X25WRE is an IP65-rated unit listed for wet locations, and is resistant to corrosion and the ingress of dust and dirt. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or “duty cycle” accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each LED based upon the LED’s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 100% capacity without overheating or visible loss of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually on or off. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 50,000 hours. LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life. LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases, vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps. CREE Specific: This lamp uses Cree LED units that have been chosen for their high lumen per watt ratio and extreme longevity. These Cree LEDs generate a robust 78 lumens per watt effective lumen output and have a 80% lumen retention at 30,000 hours, giving them better efficiency and operational life than traditional light sources. Specifications / Additional Information LEDLB-40-CPR-2X25WRE 40" Dual Spot LED Light ETL Listed Lamp Type: LED IP65 Total Lumens: 17,200 Lumens: 11,700 Wide Spot | 5,500 Narrow Spot Special Orders- Requirements Beam Type: Wide Spot and Narrow Spot Contact us for special requirements Toll Free: 1-800-369-6671 E-mail:[email protected] 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement. Scroll Down to Purchase-